3d20
185 3d models found related to 3d20.thingiverse
A quick design for a 3d20 dice holder to keep track of portent/greater portent.
thingiverse
This is the foot for a dremel 3d20 ideabuilder printer. ...I used TPU filament to print.
thingiverse
Side panel for Dremel 3D20 that allows for filament from an outside spool holder and multiple tools.
cults3d
Adapt other filament rolls to 3d20 dremel printer . Complete with spacer for even narrower rolls . ...The newer ones with cardboard sides will not fit so i have made an adapter to fit on top of removable cover.
thingiverse
If you have a 3D20 and are intending to use non-Dremel brand PLA, then this vent will allow the plastic to be fed into the print area from the outside without having to leave the top of the printer off. I designed this with custom supports because...
thingiverse
This was modified from a version found on GrabCAD (https://grabcad.com/library/dremel-3d20-filament-spool-holder-1) and improvements could still be made. I would probably port the main arm a little more to save filament, but it is very strong and the...
thingiverse
Pop one of the side air grills off your 3D20 and replace it with this. Or hey do both sides! I've always intended to re-design and re-make but it's still holding all the things. So here it stays. Bottom right corner had curling issues. Didn't know...
myminifactory
A side-mounted bracket for the Dremel 3D20 that holds a 1 Kg Hatchbox spool. The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. ... I used the...
thingiverse
I have been looking for a heattower for the Dremel 3D20 for a long time, trying to figure out how to make one. To spare you that, I will explain it here. I have also uploaded the G-Codes directly for those who just want to download and use it...
thingiverse
A side-mounted bracket for the Dremel 3D20 that holds a 1 Kg Hatchbox spool. The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. I used the...
cults3d
A side-mounted bracket for the Dremel 3D20 that holds a 1 Kg Hatchbox spool. The plate supports are just an extra precaution, sometimes the plate wanted to pop off the printer when bumped, like loading and unloading the filament. I used the...
myminifactory
Remixed from the Flashforge Spool Holder by @toolman207 Trimmed the sides down by 2mm each, as well as replaced the wingnut with a twist in place friction lock, that doesnt require the bolts and glue. Filament guide has been tapered to make the...
thingiverse
This is a mount for the Dremel 3d20/Idea Builder to hold a gopro. ...Need supports to print
thingiverse
This is a Dremel 3d20 printer spacer for the hacked holder unit here... ... https://www.thingiverse.com/thing:1160115 Full article @ http://www.techinterchange.com.au/?p=866
thingiverse
This is a remix of Prot0typ1cal 's https://www.thingiverse.com/thing:3141321 that I revised so it would fit my Dremel 3d20. ...It should also fit a Flashforge Dreamer nx as it is a similar design.
thingiverse
An external filament spool holder for the 3D20. And yes, that's a pencil! ...I didn't include the spool adapter as those may vary with manufacturer (I think - I'm only just getting into 3D printing).
thingiverse
After looking for a simple spool holder that would fit on the back of the IdeaBuilder 3D20, I decided to make my own. ... This is a very simple design, and it is a relatively fast print too.
thingiverse
This is a smaller spool rod holder that I designed perfect fit for Inland filament for the Dremel 3D20 / Flashforge Dreamer This is compatible with https://www.thingiverse.com/thing:652415
pinshape
After looking for a simple spool holder that would fit on the back of the IdeaBuilder 3D20, I decided to make my own. ... This is a very simple design, and it is a relatively fast print too.
thingiverse
This is a bearing pillow block/mount for the Dremel 3D20 3D printer. ...When I acquired the printer is seemed to have gone through a number of these (probably due to bad alignment).
thingiverse
This is an x-carriage that allows for use of flexion extruders on the Dremel 3d20. ... the .stl of the part is for use with your own slicers and the .gcode is in the event you are using one of Dremel's slicers that don't support supports that would...
thingiverse
If you have a Dremel 3d20 printer and would like to install a second right-hand-side filament spool, then having a second filament guide is a must. This is simply a (uselessly accurate: I couldn't help.. Something autistic suddenly roared deep...
thingiverse
Trimmed the sides of the original plate down by 2mm each to fit the 140x120mm opening on the Dremel 3d20, as well as replaced the wingnut with a twist in place friction lock, that doesn't require the bolts and glue. Filament guide has been tapered...
pinshape
Summary If you have a Dremel 3d20 printer and would like to install a second right-hand-side filament spool, then having a second filament guide is a must. This is simply a (uselessly accurate: I couldn't help.. Something autistic suddenly roared...
thingiverse
Just a simple riser to allow use of larger external filament spools on the 3D20 or Flashforge Dreamer. No, they don't stack, I would have made them stack but this is my first draft and it worked well enough. They don't have sloppy tolerances but...
myminifactory
This is a filament hanger/holder designed to fit on the top rim of the Dremel 3D20. Holds the filament spool from other brands since they don't usually fit inside. Dremel's own branded spools do fit inside (they are smaller and less thicker), but in...