3dlabprint

The motor mount: I modified the original 3DLabPrint mount so it can take the stock motor mount that the Multiplex Funjet uses, which made it much easier for me to mount my 28mm inrunner motor. Mount Formers: This helps to keep the motor...

My other designs for the 3dlabprint P-38 can be found at the following links: Motor mount: https://www.thingiverse.com/thing:4078761 Wheels: https://www.thingiverse.com/thing:4078785 ESC mount: https://www.thingiverse.com/thing:4175154 Pushrod...

I'm utilizing the outstanding Oshkosh M-ATV body from 3dlabprint for my SCX10 chassis. Since the body lacks a sleek interior, I've developed one on my own. The interior is not 100% scale accurate since you don't have a flat floor and due to printing...

Custom spinner for 3DLabPrint Piper Pawnee (Dusty). The spinner is assembled from 2 main parts, which are aligned to each other by an alignment ring - formed from a piece of filament. The alignment ring also acts as a stabilizer for the front part...

Aligning the horizontal stabilizers on 3dLabPrint 1/12th warbirds has always been a bit tricky for me. They often don't come out perfectly level and act strangely once the elevator is attached. This is designed specifically for the Spitfire MK XVI...

Update: 2 more fine hinges to print on Flex Petg I'm building an RC 3Dlabprint model, and I noticed that the hinges sold at RC shops are overpriced - 5.50 euros for 10 tiny hinges! So, in 5 minutes, I created three versions of hinges compatible with...

Wheels for P-38 from 3dlabprints. Main wheel - 70mm in diameter. Front wheel - 50mm in diameter. Print settings: Rims - printed from PETG. Layer height - 0.2 mm Outlines/perimeters - 1 Top/bottom layers - 4 Important - option for allowing single...

The Zero (https://3dlabprint.com/shop/a6m2zero/) is amazing and very fun & easy to fly model!However, I felt like adding a few upgrades here & there to make it better meet my needs.This is a work-in-progress post, I'll keep adding new upgrades and/or...

This is a custom motor mount I designed specifically for the 3dlabprint Stearman Kaydet. The standard mounting setup has you attaching the motor to the very front of the engine block. This means the wires are also in this position, requiring them to...

Here is my design of a reinforced spinner for the 3Dlabprint Piper Pawnee. It's an impressive achievement that this redesigned spinner weighs only 2g more than its original counterpart yet boasts significantly enhanced strength, and as seen in the...

Human: Complete Tail Assembly for 3DLabPrint 1/12 Corsair. This thing replaces the original PP multi-wall sheet tail with 3D printed parts. ---------------------------------------------------- 2019.03.23: Update on Description: 1.) To give...

Reinforced Motor Mount for the Piper Pawnee from 3DLabPrint. This modification provides several key features: * It utilizes the original SK3 (3542) metal motor mount plate for reinforcement. * A cooling channel is integrated into the motor mount to...

Print the covers from LW-PLA, the supports from regular PLA.Form the covers with warm air.

3D printing enthusiasts rejoice at the innovative Stearman FPV top wing clip, precision-crafted from PLA for optimal stability and durability. Designed specifically to accommodate the 1177 camera and Eachine VTX03, this clever clip ensures seamless...

I had to design and build a custom mount from scratch for my trusty 2836 NTM motor. Fortunately, the process wasn't too complicated - I just needed to adapt it for other brands that use M3 screws with a 16x19mm thread size. ...It's always satisfying to...

Recomended motor for this plane was not available, so i bought FOXY G3 Brushless Motor C2012-2000, but it had no prop shaft and i could not get anything that fits the motor and recomended propeler. So i designed propshaft to be printed and it works...

Spinner cone fits the FMS Bf109 (1400) Spinners backplate and prop blades.

Human designs innovative B25J gun barrel utilizing 3D lab print technology.

Remixed poharatek's excellent design to suit the Hurricane and MG90S or SG90 servos. Rotated the fairing 180 degrees relative to the base so it would work for the Hurricane and increased its height to provide more protection for the long aileron...

These are .50 barrels I made specifically for the 3Dlabprint B-25. ... Printed excellent on a my Phrozen Sonic Mini

A simple wheel cap to glue onto the factory rim of the 3DLabPrint Piper J-3 Cub. ...I used a low-profile, button-head machine screw to attach my rim to the main gear legs.

... chuck up a sewing needle in a pin vise and scribe until your window pane comes free. 4 holes so that you can pin down the cutting guide over your material for easy slip free cutting. https://www.thingiverse.com/thing:2257761 GO 3DLABPRINT!

I Designed a Lipo Mount for the Zivko Edge 540 V3 (1.62m/64in Wingspan) That Works Perfectly with Any Other 3dlabprint Model Since I Couldn't Find a Suitable Bracket, I Decided to Create One Myself All You Need to Do Is Glue It in Place and Secure It...

... mout is, of course, in rear position, where you can use screwtable shaft and all entire motor's bell better than front not screwtable shaft! ...I drawed this piece for Dusty 3dlabprint plane fort all 35 size motors. ... Tight, solid, good, awesome!!

I made some custom wing servo covers for the 3dLabPrint Hawker Hurricane. These are most useful for the version of the plane for belly landings. Hopefully they will protect the aileron and servo horns. They are made in LWPLA but in a higher...

Lipo mount for the Zivko Edge 540 V3 (1.62m/64in wingspan) by 3dlabprint (ore any other) Because I didn't find a suitable bracket, I made one :-) Just glue it and use some velcro straps for fixing. ...My 2 x 4S 3600mAh fits perfectly</p> <h3> Print...

Wing Guide for Stabilizing the 3DlabPrint F4U Corsair 1:12 Wing. The wing stabilizer fixes left-right wobbling during flight, keeping it centered until landing. However, in case of a collision, releasing the stabilizer is essential to prevent...

Print instructionsCategory: R/C Vehicles Summary Here is my design of a motor mount for the 3Dlabprint Slingblade. With this motor mount you can install a Racestar 4108 in your Slingblade. Propeller 9x6 6S / 1300 mAH LiPo ESC 40 Amp Very hot...

Print instructionsCategory: R/C Vehicles Summary Here is my design of a motor mount for the 3Dlabprint Slingblade. With this motor mount you can install a Racestar 4108 in your Slingblade. Propeller 9x6 6S / 1300 mAH LiPo ESC 40 Amp Very hot...