3dr iris case
202337 3d models found related to 3dr iris case.myminifactory
Float platforn for the long tube legs on the Iris and Iris +. Cut pool noodles to 5.25 long and taper the tops so the noodle does not block air flow to the motors. Use double sided stickey tape to re-install the rubber feet. I want to add be sure to...
thingiverse
Float platforms for the long tube IRIS legs, Cut pool noodles to 5.25 in long, taper the top so it does not block the air flow to the motor, install the pool noodle on the support and slide the support on the tube, use some double sided sticky tape...
grabcad
I printed this model to hold electro permanent magnets for the 3DR Iris +. This EPM holder was 3D printed using the ABS plastic and is attached onto the Iris body using the gimbal mount's threaded holes. ...One drawback was the instability due to the...
thingiverse
I designed this because I did not found any model based on the original, to replace a lost rubber foot of my 3DR Iris+. Have not tried printing it with TPU (which seems to be the perfect material for this), only ABS. The print pictured above...
thingiverse
New version - http://www.thingiverse.com/thing:1697237 The mount is designed around my LG G2 in an Incipio case. Modify the clips for other applications. The pieces were printed in PLA at .2 mm layer height and 100% density. The center mount piece...
myminifactory
... the the triangle piece to the door and hot glue to secure the led cover to the triangle piece. Not sure if it'll fit the original iris but i don't see it as a problem. ... heres a video of it in operation http://youtu.be/eOrgSR_q_FE
thingiverse
This is a light weight landing gear for a 3DR Iris drone, snaps directly to the arms. I uploaded two versions, one for FDM and other for SLS, The one is separately, which contains feet, feet mirror and clip are for FDM, Just make sure the flat part...
thingiverse
Based on http://www.thingiverse.com/thing:320642, but needs no case (my printer isn't big enough to make one). Added a bit of a tilt to the base to bring the tablet forward. ... Mounted by replacing existing screws with #6-1.5"
thingiverse
The mount is designed around my LG G2 in an Incipio case. Modify the clips for other applications. The pieces were printed in PLA at .2 mm layer height and 100% density. The center mount piece is tapped with M3 threads. Printed pieces hold...
thingiverse
I can now put the transmitter in my case without having to remove the mount. The pieces were printed in PLA at .2 mm layer height and 75% density. The center mount piece is tapped with M3 threads. Printed pieces hold threads well. M3x25 socket...
thingiverse
This is a case for a 3DR radio for the IRIS, IRIS+ or other drones so it can be attached to the lid of your MacBook Pro ground station instead of just dangling off the USB wire and lying in the grass being gnawed at by rodents. There is a cut-out...
thingiverse
Simple 3-part 3dr uBlox GPS Case for use with reflector Instructions This is a simple three-part 3dr uBlox GPS case. I was looking for an easy way to fit a reflector under the GPS to improve performance. ...Use thin metal film between bottom (shield)...
youmagine
This adapter only uses the holes on the outside rim for mounting.This part is modified from Richrap's original designs for the 3DR printer that can be found on his website:www.richrap.comYou will also need to print the spacer part, otherwise the case...
thingiverse
A small case to protect your 3DR telemetry module. It weighs 9g with 15% infill. Please hit "like" if you like it :-) Instructions Just print it :-) Maybe you have to scale it x10. My .stl...
prusaprinters
This is the MinimOSD 3DR OSD Case by Stanleykuenzle, with a modified Case Top with holes for VTX and Camera Plugs coming out of the top as well as a Hole for the MinimOSD Reset. I make no claim to the design and creation of these files. They are the...
thingiverse
This is the MinimOSD 3DR OSD Case by Stanleykuenzle, with a modified Case Top with holes for VTX and Camera Plugs coming out of the top as well as a Hole for the MinimOSD Reset. I make no claim to the design and creation of these files. They are...
thingiverse
If you have the newer radio that didn't come in a case, try this -- http://www.thingiverse.com/thing:712588 Housing for the 3DR radio "Air" module. Instructions Printed on a printrbot with .35 mm...
thingiverse
Case for 3D robotics GPS module. ... Instructions Glue it together for permanence!
thingiverse
The case for the telemetry are half-through design, i.e meaning 1 side of the case is open and the other side with opening for the antenna receptacle only.
thingiverse
A small case to protect your MinimOSD. It weighs 9g with 15% infill. Please hit "like" if you like it :-) Instructions Just print it :-) Maybe you have to scale it x10. My .stl files from...
thingiverse
3DR IRIS mounting bracket for DYS 3 axis Gimbel Also join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/ Instructions 3DR IRIS mounting bracket for DYS 3 axis...
myminifactory
3DR IRIS mounting bracket for DYS 3 axis GimbelAlso join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/
thingiverse
I want to improve the 3DR Iris+ model for small 3D Printers in the home. I sliced the frame arms to allow 16mm Carbon tube to be used. You can choose the length of tube to increase or decrease propeller size. I did not use support material to print...
myminifactory
A case to hold a FatShark 700 tvl camera and an ImmersionRC 600 mW transmitter on the front GoPro mount of a 3D Robotics Iris. The transmitter box has front and rear cutouts to promote airflow. The transmitter is held in place mainly by the antenna....
myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2013 version of the Nexus if you have a 2012 version check out this Mount I made for the 2012 version
myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 version
thingiverse
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 versionhttp://www.thingiverse.com/thing:591294 Also...