3dr iris plus
45174 3d models found related to 3dr iris plus.myminifactory
Float platforn for the long tube legs on the Iris and Iris +. Cut pool noodles to 5.25 long and taper the tops so the noodle does not block air flow to the motors. Use double sided stickey tape to re-install the rubber feet. I want to add be sure to...
thingiverse
Float platforms for the long tube IRIS legs, Cut pool noodles to 5.25 in long, taper the top so it does not block the air flow to the motor, install the pool noodle on the support and slide the support on the tube, use some double sided sticky tape...
grabcad
I printed this model to hold electro permanent magnets for the 3DR Iris +. This EPM holder was 3D printed using the ABS plastic and is attached onto the Iris body using the gimbal mount's threaded holes. ...One drawback was the instability due to the...
thingiverse
I designed this because I did not found any model based on the original, to replace a lost rubber foot of my 3DR Iris+. Have not tried printing it with TPU (which seems to be the perfect material for this), only ABS. The print pictured above...
myminifactory
... the the triangle piece to the door and hot glue to secure the led cover to the triangle piece. Not sure if it'll fit the original iris but i don't see it as a problem. ... heres a video of it in operation http://youtu.be/eOrgSR_q_FE
thingiverse
... entirely sure it was necessary but I didn't want the screw turning. The well in the thumb screw holds an M4 nut. iris_phone_bracket1a.stl has a simple bracket with a shorter thumb screw. ... It works fine, but it just didn't feel secure enough.
thingiverse
This is a light weight landing gear for a 3DR Iris drone, snaps directly to the arms. I uploaded two versions, one for FDM and other for SLS, The one is separately, which contains feet, feet mirror and clip are for FDM, Just make sure the flat part...
thingiverse
3DR IRIS mounting bracket for DYS 3 axis Gimbel Also join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/ Instructions 3DR IRIS mounting bracket for DYS 3 axis...
myminifactory
3DR IRIS mounting bracket for DYS 3 axis GimbelAlso join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/
thingiverse
I want to improve the 3DR Iris+ model for small 3D Printers in the home. I sliced the frame arms to allow 16mm Carbon tube to be used. You can choose the length of tube to increase or decrease propeller size. I did not use support material to print...
myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 version
myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2013 version of the Nexus if you have a 2012 version check out this Mount I made for the 2012 version
thingiverse
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 versionhttp://www.thingiverse.com/thing:591294 Also...
thingiverse
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2013 version of the Nexus if you have a 2012 version check out this Mount I made for the 2012 versionhttp://www.thingiverse.com/thing:591287 Also...
myminifactory
A case to hold a FatShark 700 tvl camera and an ImmersionRC 600 mW transmitter on the front GoPro mount of a 3D Robotics Iris. The transmitter box has front and rear cutouts to promote airflow. The transmitter is held in place mainly by the antenna....
thingiverse
you can fit a Maxbotix rangefinder LV in it, and clip it without bond or tape under a Iris plus arm. the XL series rangefinders (with the big potentiometer on the PCB) are incompatible, just the LV serie will fit in it. ...PLA is good, ABS also fine.
thingiverse
Replaces the fixed GoPro mount, fits Eachine/Elgae mini fpv camera/transmitters. ...Example: http://rctimer.com/product-1453.html
thingiverse
This is still a work in progress but is available to print. The hardware needed to complete this mount is from McMaster Carr part # 94510A240 as well as M3 flathead screws. ...Vibration Isolation mounts are from DJI
thingiverse
Iris+ replacement door and latch for 3drobotics iris plus. ... I am working on making the LED mount onto the header bolt, should be done soon to prevent battery pinches
thingiverse
Iris+ replacement door and latch for 3drobotics iris plus. ... I am working on making the LED mount onto the header bolt, should be done soon to prevent battery pinches
thingiverse
Made from glass material to hold a led strip to be used as a front light for 3DR Iris Plus. ...Can be mounted on the Gopro mount.
myminifactory
This adapter is used to mount the FY-G3 Gimbal on the 3DR IRIS.
myminifactory
3DR IRIS sky hero type landing gear Also join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/
thingiverse
3DR IRIS sky hero type landing gear new version is coming soon it will support more gimbles and be printable with no supports and now features are stronger design Also join the 3D Robotics IRIS Owners Page...
thingiverse
put the transmitter inside secured it with some 2 faces tape (optional, it should work well even without tape), and just clip it under a leg of your IRIS plus, then fly! PRINT IT IN ABS, NO PLA!! PS: I put a 0.5mm thick aluminium sheet to act as a...
thingiverse
This adapter is used to mount the FY-G3 Gimbal on the 3DR IRIS. Instructions The small tubes are used to attach the gimbal to the adapter. you will need (number of 8x) M3 screws as well. ...The length...
thingiverse
it mounts into the not used antenna hole in the flysky transmitter 150mmX110mm It should work for all 7-8 inch tablets Also join the 3D Robotics IRIS Owners Page https://www.facebook.com/groups/635611993176188/ Instructions all you need to fix the...