3dr radio
14085 3d models found related to 3dr radio.thingiverse
If you have the newer radio that didn't come in a case, try this -- http://www.thingiverse.com/thing:712588 Housing for the 3DR radio "Air" module. Instructions Printed on a printrbot with .35 mm...
thingiverse
This is a case for a 3DR radio for the IRIS, IRIS+ or other drones so it can be attached to the lid of your MacBook Pro ground station instead of just dangling off the USB wire and lying in the grass being gnawed at by rodents. There is a cut-out...
thingiverse
These parts will hold a 3DR ground radio vertically so it doesn't have to be connected directly to your laptop. Snaps together. Instructions All these parts can be printed flat and then press-fit...
thingiverse
This is a custom dock for a 3dr radio (SiK radio v2). It houses a ble mini, slide switch, 18650 battery and charge/regulator circuit A blank top model is also included if you wish to use this for other telemetry radios that do not fit in the regular...
myminifactory
EDIT [3/11/2015]: A larger multi-purpose case is here - http://www.thingiverse.com/thing:719615 Changes for the v.2 3DR Radio are a smaller connector gap and the case is slightly longer. This case extends beyond the base of the antenna connector to...
thingiverse
EDIT [3/11/2015]: A larger multi-purpose case is here - http://www.thingiverse.com/thing:719615 Changes for the v.2 3DR Radio are a smaller connector gap and the case is slightly longer. This case extends beyond the base of the antenna connector...
thingiverse
A cover for HobbyKings 3dr-Radio grund module. ...Updated hole location in the cover lid.
thingiverse
... 2 pieces together like on the photo's. ...snap in the 3DR radio .. Install Andropilot, and you're all set ! Instructions Glue the 2 pieces together like on the photo's. ...snap in the 3DR radio ..
thingiverse
Ich habe hier ein "Slim Case" für das Air Modul der Pixhawk/APM Telemetrie gedruckt, es ist kleiner, verfügt über löcher für Kabelbinder und hat ein "Sichtfenster" für Kabelbinder. Dank eines Einrast Mechanismus kommt das kleine Gehäuse komplett ohne...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3kd2kuzulfT
thingiverse
I use this as a GCS with a 3DR radio. The pieces were printed in PLA at .1 mm layer height and 100% density. The center mount piece is tapped with M3 threads. Printed pieces hold threads surprisingly well. M3x12 socket head screws hold the clips to...
thingiverse
Case for: Update 11/17 - V2 uloaded changes: Remove: GPS antenna hole removed Add: New hole for radio LEDs GPS CRIUS u-Blox CN-06 GPS Receiver V2.0 from RCTIMER http://www.rctimer.com/product_763.html and RCTimer Radio Telemetry Air Module, same size...
thingiverse
... a bit like a spegatti ball with all the wires and little components all over, made this case to neatly fit all the components, much cleaner. ... RCTimer AIOP MultiWii v2.0 RCTimer UBLOX CN06 GPS RCTimer MultiWii Bluetooth Module HobbyKing 3DR module.
thingiverse
This part is a nice container for a FatShark FPV radio + the 3dr telem radio. Both parts sit cleanly and can be tightened in with a single zip-tie. Be careful pulling the ziptie, the output walls are a bit too thin and mine cracked(still in...
thingiverse
Purchase upgraded mounts at http://www.maxxuav.com This is used to hold two Sunhans 2.5W Amplifiers & Battery and mount to the 3DR Solo Radio. ...I used amplifier & battery from FPVLR.com
thingiverse
My things: APM 2.6 http://store.3drobotics.com/products/apm-2-6-kit-1 Telemetry http://store.3drobotics.com/products/3dr-radio-telemetry-kit-433-mhz Minim OSD http://store.3drobotics.com/products/apm-minimosd-rev-1-1 FatShark AttitudeS...