3drobotics
48 3d models found related to 3drobotics.
myminifactory
UPDATE - 3DR IRIS+ Clip now included 3D Robotics have been strong adovcates of open source collaboration and their IRIS+ and MADE FOR SOLO projects are testimony to that. If that wasn't enough, in all their awesomeness they have decided to give...
thingiverse
IRIS + Folding Long Legs 3drobotics These are so you can fold your legs down without taking them off. Very beta, they have not been tested. 7mm Graphite dowel is needed. ... Instructions Imagination and...
myminifactory
Iris+ 3drobotics drone snow and sand shoes so it does not sink in mud, snow, sand ect
thingiverse
Iris+ 3drobotics drone snow and sand shoes so it does not sink in mud, snow, sand ect
thingiverse
3dRobotics Iris+ longer and lighter legs these do not have the set screw yet, I will add it soon. Using Graphite 7mm rods to make the legs longer and lighter. Printed in ABS 5 grams each leg. ... ...
thingiverse
Iris+ replacement door and latch for 3drobotics iris plus. ... I am working on making the LED mount onto the header bolt, should be done soon to prevent battery pinches
thingiverse
Iris+ replacement door and latch for 3drobotics iris plus. ... I am working on making the LED mount onto the header bolt, should be done soon to prevent battery pinches
myminifactory
Iris+ 3drobotics replacement legs long legs to protect gimbal. These can also be short legs too. Used 7mm graphite tubing to keep the weight down, 30% fill rate ABS works great with 3 shells, no supports needed. ... I would recommend making 8 of them...
thingiverse
Iris+ 60% weight Reduction arms for 3drobotics. These are about 16grams each using the 7mm rods, they protect the wires and are a huge reduction in weight. Work in progress, need to put the voids into the base that attaches the knuckle to the...
thingiverse
Short and long leg combo Iris+ 3drobotics Drone UAV These can be short legs without the dowel or long legs with a dowel I HAVE NOT TESTED THIS VERSION, but it should work. Made these a little thinner trying to keep the weight under 10g with 2 leg...
thingiverse
Iris+ 3drobotics replacement legs long legs to protect gimbal. These can also be short legs too. Used 7mm graphite tubing to keep the weight down, 30% fill rate ABS works great with 3 shells, no supports needed. ... I would recommend making 8 of them...
thingiverse
This is a leg (3 are needed for a full set) to replace the PCB legs that ship with a 3DR Y6 multicopter. I broke the legs on mine and lost many of the spreader pieces. Note that you can use a lower infill density to make the weight of these legs...
thingiverse
Iris+ replacement foot cap for 7mm legs and thinner 3drobotics uav drone plus
myminifactory
Iris+ replacement foot cap for 7mm legs and thinner 3drobotics uav drone plus
thingiverse
This is a replacement for the telemetry antennas that come with the radios. I made half wave dipoles using the IBCrazy formula based on my 0.4mm diam. cable. Each pole is therefore 7.6mm long. ... You can find details here:...
thingiverse
Is your Iris+ over weight, do you want longer flight times and better handling with reduced vibration? Well if you do you have not found the right thing to print. ...This is a work in progress!
thingiverse
This is a version of the Iris+ Graphite Arms that connects to the body, Should get close to a 60% weight reduction on the arms. I have not printed this one, but the holes should line up. I have no idea where to get the brass standoff inserts. ... ...
myminifactory
Is your Iris+ over weight, do you want longer flight times and better handling with reduced vibration? Well if you do you have not found the right thing to print. This is a work in progress! ...
thingiverse
A 3d printed replacement arm of the Arducopter from 3DRobotics
thingiverse
Post-Printing Acquiring Components APM 2.6: https://store.3dr.com/products/apm-2-6-kit-1 Radio Set (Android Compatable):https://store.3drobotics.com/products/3dr-radio Compass Kit: https://store.3dr.com/products/3dr-gps-ublox-with-compass PDB:...
thingiverse
Enclosure for camera pcb from 3Drobotics. ... Instructions glue pins on base into the mounting holes in the cover for permanent enclosure.
myminifactory
Quanum Q-2D gimbal adapter plate for 3Drobotics Iris and Iris+ drone. ... Replaces upper the plate on the gimbal, vibration dampeners attach directly to plate elminiating extra weight and height.
thingiverse
This is a mount for Canon S100 on Iris+ Canon S100, S110, S120, SX260, ELPH 110IS, 130IS, 320HS & 330HS Fixed Mapping Mount & Adapter for 3DR Iris and 3Drobotics iris+ You just need dampening balls.
thingiverse
Landing Gear for 3DRobotics drones: X8M, X8+, DIY Quad Kit, DIY Y6 Kit Print Settings Printer: 3DCloner DH Supports: No Resolution: 0.300 Infill: Hexagonal 50% Notes: Good results with PLA
thingiverse
This is a remix of Barneyj's JR9303 phone mount. ... I modified the bottom mount to fit on the FrySky Taranis. I also modified the top mount to fit a cased Galaxy S4 and the 3DRobotics telemetry module.
thingiverse
My things: APM 2.6 http://store.3drobotics.com/products/apm-2-6-kit-1 Telemetry http://store.3drobotics.com/products/3dr-radio-telemetry-kit-433-mhz Minim OSD http://store.3drobotics.com/products/apm-minimosd-rev-1-1 FatShark AttitudeS...
grabcad
... for Jdrones Ublox GPS. ...Cable hole is sealed using normal furniture foam rubber with sticker. Tape is Gorilla "FOR THE TOUGHEST JOBS ON PLANET EARTH™" tape. 3Drobotics connector position is different and therefore it doesn't fit in to this.