3ds game card case

... be an issue either. Look at the picture as a reference when deciding how many of each part you need. I have since made a much simpler, far more effective 3DS game card case. ...It can be found here: https://www.thingiverse.com/thing:2668901

So I was looking for a small holder for my switch games and found Z80nm's model and modified it to have slots for both 3ds/nds and switch games so I can hold both. At the same time, I reduced the size and tolerances so that it is slimmer and can fit...

... groove to tell which half was the top and add some grip. Available for purchase at http://www.3dprinteddebris.com/listing/491676736/game-case-for-nintendo-ds-and-3ds-games Update 3/19/17: Added a 5 slot make to the project at a commenter's request.

Turns out if you drop one of these game cases on the ground, the shelf inside will break, and you can't buy replacement shelves! ...So here's an as-close-as-possible reproduction.

Makes it easy to organize SD cards and game cards.

I used it for 3DS games.It has a bit more space between the cards to see them. Its using a bit less material and you see the full front of the first card.You can customize the number of cards. To do this, please install OpenSCAD on your own computer...

I grabbed smants' "SD & Micro SD Card Holder" https://www.thingiverse.com/thing:2504995 and loved it so much I wanted to redesign it for 3DS games. However this is not an edited version of his, I made this file from scratch. It holds 23 games. May...

A holder for 15 Nintendo ds or 3ds game cards. ...The game cards can be flipped through to pick and choose the desired game.

A holder for 15 Nintendo ds or 3ds game cards. The game cards can be flipped through to pick and choose the desired game. ... Instructions 20% infill 0.08 mm layer height

This is a stylized Nintendo 3DS Game Card Model which can be used on a key chain. It's about the size of a Canadian/US Quarter. ... If you don't have a 3D Printer we also sell pre-printed units with a key chain at on our store at: etsy - ...

This is a remix of the DS game card box. It has a bit more space between the cards to see them. Its using a bit less material and you see the full front of the first card. You can customize the number of cards. ... Use a rubber band in the groove at...

A simple Game Holder for your Nintendo 3DS or Switch. ...Choose what Holder you want!

For holding games in the used Nintendo DS range, holds 17 cartridges. ... (DS+GBA still Work in progress, and doesn't properly fit), DS & 3DS finished use a high quality setting if you want the writing to show up

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: gutter_height = 2 number_of_cards = 5 card_spacing = 10 gutter_width = 3 box_height_addition = 15 card_spacing_ends = 2.5 $fn = 20 cube_r = 3

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: box_height_addition = 15 gutter_width = 3 card_spacing = 10 gutter_height = 2 $fn = 20 number_of_cards = 11 cube_r = 3 card_spacing_ends = 2.5

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: gutter_height = 2 $fn = 20 card_spacing = 10 cube_r = 3 card_spacing_ends = 2.5 number_of_cards = 12 box_height_addition = 15 gutter_width = 3

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: gutter_height = 2 number_of_cards = 20 card_spacing = 10 gutter_width = 2 box_height_addition = 11 card_spacing_ends = 2.5 $fn = 20 cube_r = 3

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: $fn = 20 cube_r = 3 box_height_addition = 11 gutter_height = 2 gutter_width = 2 number_of_cards = 10 card_spacing_ends = 2.5 card_spacing = 10

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: gutter_width = 3 $fn = 20 box_height_addition = 15 card_spacing_ends = 2.5 card_spacing = 10 number_of_cards = 7 cube_r = 3 gutter_height = 2

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Instructions Using the following options: card_spacing_ends = 2.5 gutter_height = 2 cube_r = 3 card_spacing = 10 gutter_width = 3 box_height_addition = 15 number_of_cards = 8 $fn = 20

##Pokebox Switch/DS/3DS Game Case This is a remix of a Pokebox that I made my son for his birthday to hold his Pokemon playing cards. We love our switch and I realized that I could easily turn the Pokebox playing card holder into a Pokebox Switch...

Allows to store Nintendo 3DS Game in DVD Case

This will hold 3DS, DS, and Switch games. The lid slides securely on top. There are 2 options for the lid, one with the Sonic recess for the logo, and a plain one with no logo. (for the non-Sonic fans) The case is in 3 pieces, or 2 if you choose to...

This is a card game case.

3DS Game box case wall mount for display. ...I haven't had a chance to fit this to a 3Ds case - let me know if the fit is good and if any changes should be made.

3DS Game box case wall mount for display. ... I haven't had a chance to fit this to a 3Ds case - let me know if the fit is good and if any changes should be made.

A little box-shaped case for Nintendo Game Cards. ... Supports: Nintendo DS, Nintendo DSi, Nintendo 3DS, Nintendo Switch

Supports several case sizes: - DS EU version: 22mm case width - DS US version: 18mm case width - 3DS version: 17mm case width You can store them neatly and grab one without knocking the rest over. There are slots at the back to make it easier to get...

This model is a solution for displaying your 3ds games with cases. It is modular and stackable. ...Print as many as you need to show off your game collection!

There are some great 3DS game cartridge holders already on Thingiverse, but I couldn't find one compact and without something like a hinge. So here's my entry into the "3DS Cartridge Case" arena. It'll hold three games, 3DS or DS, and has a sliding...