3rd gen 4runner rear window storage 3d models

It replaces the door interior window lift cover holder. 05.03.2018 I added some minor improvements and fixed a bug. This detail is for replacing a broken component in the vehicle GreatWall Safe. It takes the place of the button lever holder on the...

A nail or whatever should work. It works great on my window. I don't know how much tolerance the factory had when putting these things together, so it may or may not work in your truck. I only have the one to test with. ...I've included the Fusion 360...

The window cutout is fine, and this just means that the inside guide will only fit in one orientation. It's such a non-issue that it wasn't worth fixing the model, but may confuse you at first. To use :1- Place the guide against the back wall of the...

You can find 3Dmodels and more detailed info here: BMW E36 gear : https://cults3d.com/en/3d-model/various/bmw-e36-rear-window-vent-gear Range Rover HSE: https://cults3d.com/en/3d-model/various/range-rover-hse-rear-wiper-gear Sample gear won´t fit,...

made for a 3rd gen 4runner but probably fits a fair amount of Toyotas. sized to print from ABS, but it might fit with other filaments. The two prints are made to slide to close the vents if needed, Right now it slides back and forth too easy so...

My take on adding cup holders to a 3rd gen 4runner (pre-1999). This fits like a glove in my 1998 4WD. It is secured down with just some double sided tape. This is the first version I made expecting to need to refine it in the future, but it is...

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515 rc4wd storage container for back cab window on toyota 85

This mount lets you swap out your current sunglasses rack for a six-switch sPod on your 5th Gen 4Runner. Please note that this mod is specifically designed for vehicles without crawl control. ...If your 4Runner has a built-in sunglasses holder, it's...

This is a Center Console insert for a 5th Gen 4Runner.  I have it in a 2022 but should fit other years.  Added Sasquatch for the kids.   Only use PETG or ABS. ... Follow directions for your favorite filament.

/!\ UPDATED 09/2021 /!\ Addition of optional rings GG3_V2_Optional_Joint_1.stl -> need for supports GG3_V2_Optional_Joint_2.stl -> need for supports GG3_V2_Optional_Joint_3.stl -> need for supports GG3_V2_Optional_Joints.stl (3 in 1) -> need for...

<p>Here are many parts to mix'n'match. I did not print-test every single model and combination (e.g. smooth base and smooth top work fine).</p> <p>One primary goal was to not cover the light ring, so I didn't. :)</p> <p>Oh, I do not expect anyone to...

I created a custom replacement component that transforms the side dash pocket into a sturdy shelf, specifically engineered to securely hold a brake controller. ...This innovative design is tailored to accommodate the Tekonsha 90160 Primus IQ Electronic...

- Printed the updated model with Inland PLA on my MK3s+- Used a 25% infill and three perimeter layers The print came out great, but keep in mind that the adapter is on the smaller side so to avoid any adhesion issues, you might want to use a brim or...

The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: *.max (3ds Max 2008 scanline) *.max (3ds Max 2008 vray) *.fbx (Multi Format) *.obj...

Helps to keep objects from sliding around in the upper portion of the glove compartment. Fits a third generation Prius perfectly and likely also fits the second generation as the dimensions appear to be very similar. For added stability, use rubber...

Resize of bolt opening to fit newer Defiant deadbolts. ...

Use this simple jig to ensure your new Lokbuild print surface is installed perfectly to your Cube3 print plate. You'll need to print 4 of these and a 203mmx203mm Lokbuild print surface. Lokbuild is a MUST have for anyone hoping to print ABS with this...

I took the awesome tie fighter by https://www.thingiverse.com/CaiotE and made one small tweak and added one new piece: 1) Increased the size of the square pegs/slots for wing attachment, to add a little strength. 2) Created a base to set the...

This part slides onto the existing volume knob. For me, the friction fit was perfect with my print - no glue was used. Your fitment results may vary though. It may wilt during the summer heat. ...We shall see.

This is a redesign of Litesaver's original cupholder. This cupholder has been redesigned to fit larger cups. The original could only fit small water bottles and cans. With this new redesigned cup holder, you can now fit much larger drinks from fast...

I've remixed the file from Breadycorn, because I wanted more details for the Base. The Stargate itself was detailed enough. ...Only an update for the base.Thanks to the origin files: https://www.thingiverse.com/thing:4825357The Stargate fits realy tight...

Here are many parts to mix'n'match. I did not print-test every single model and combination (e.g. smooth base and smooth top work fine). One primary goal was to not cover the light ring, so I didn't. :) Oh, I do not expect anyone to try the lattice...

Here's a modified version of the design that accommodates an IT power supply by increasing the size of the hole. I made only one alteration to the original design, found at https://www.thingiverse.com/thing:3273420, to allow for the use of an IT...

printed in PLA It took ~13h to print holder + screws on MK4, used the tree supports with front side facing down

Remixed from the following models: https://www.thingiverse.com/thing:3224790 https://www.thingiverse.com/thing:1873213

I designed a replacement part for my 2012 Ford Focus's worn-out parcel shelf hinges, specifically targeting the inner (center) component. My goal was to create a larger surface area that can be securely attached to the possibly damaged parcel shelf...

<p>Wenn man zum Beispiel im Stereo System eine stumm schaltet und kein rotes Licht möchte.</p><h3>&nbsp;</h3><h5>edit:</h5><p>Haha mir fällt grad auf ich hab ein Loch fürs Mikrofon rein konstruiert...

I added a cable organizer to the base, giving it a fresh remix of the original V2. Still utilizing PLA/PETG, one of the two small tabs in the middle section tends to break often, but it will still snap together securely. My build time came in around...

I found the design by the original designer to be great, but unfortunately a little unstable. I designed this base plate that the housing and legs sit in. ... The echo clock is simply glued into the insets.