3x5 notepad holder 3d models
322091 3d models found related to 3x5 notepad holder.cults3d
This is a notepad case for your standard 3x5 notepad that has wires up top. After years of having my small field notepads destroyed by placing in my uniform pocket, I came up with this solution. Just simply print and stick your pad in it. Printed...
thingiverse
This is a notepad case for your standard 3x5 notepad that has wires up top. After years of having my small field notepads destroyed by placing in my uniform pocket, I came up with this solution. Just simply print and stick your pad in it. Printed...
thingiverse
... it up right so it doesn't need supports. I also recommend setting the infill to 50% or more since it is very thin plastic. Pencil holder hole is 8.5mm wide in diameter. Notepad slot diameter is 2mm.I used Velcro to hold the holder onto my fridge.
pinshape
Made this quick design for storing notepads for the kids. ... Very easy to print and no supports needed Printed with PLA but any material should be fine Nozzle Temp = 200 ˚C Bed Temp = 50 ˚C Layer = 0.3mm (can print smaller but will take a bit...
thingiverse
I wanted a notepad and writing utensil holder that I could hang on the wall in my barn. Can be hung from #8 or #10 screws (probably others too). Holds notepads up to 5" wide (modeled specifically for the Jr. Legal Pads). ...The pen holes are 15mm...
thingiverse
A fun little project to replace the broken pad holder I keep in the car. ... It holds a 2 3/4" x 4 3/4" (70mm x 120mm) notepad.
thingiverse
Upright notepad holder. ...Basically made for gaming so i could have my notes displayed right in front of me so they are easy to see Hope you find it useful yourself!!a Cheers!
thingiverse
These unlike the commercially available ones are not ridiculously expensive and do not require custom (and also expensive) refills but are designed to take common note-let, pad, card refill sizes The Groovy Notepad holder takes the long slim style...
cults3d
This notepad holder still uses a rubber band, but it makes the notepad easier to use. This is sized for paper that is approximately 4.25" x 3.67". That's one standard sheet cut into 6 pieces. See the picture for an example of how to cut. There is a...
thingiverse
Removed the bottom holder part for folded single papers instead of an actual notepad. Moved the pen holder upwards for the pen clip to grab onto. ...Remix/modification was requested by my mother for work and she likes it while also admired by her...
thingiverse
This notepad holder still uses a rubber band, but it makes the notepad easier to use. This is sized for paper that is approximately 4.25" x 3.67". That's one standard sheet cut into 6 pieces. See the picture for an example of how to cut. There is a...
thingiverse
This a 3-d printed notepad holder for lists on a magnetic surface (refrigerator). My wife was looking for ones to buy. Everything we could find was expensive and/or nonrefillable with standard paper. This design is made to fit standard...
prusaprinters
This notepad holder still uses a rubber band, but it makes the notepad easier to use. This is sized for paper that is approximately 4.25" x 3.67". That's one standard sheet cut into 6 pieces. See the picture for an example of how to cut. There is a...
prusaprinters
Made this thing so I could attach my notepad to my wallet and stop forgetting to bring my notepad with me.
prusaprinters
I wanted a notepad and writing utensil holder that I could hang on the wall in my barn. Can be hung from #8 or #10 screws (probably others too). Holds notepads up to 5" wide (modeled specifically for the Jr. Legal Pads). The pen holes are 15mm...
thingiverse
An add on for the VelocityOne controller to add a notepad clipped to the throttle arm. ... UPDATE - Added a version that sits horizontally.
prusaprinters
A fun little project to replace the broken pad holder I keep in the car. It holds a 2 3/4" x 4 3/4" (70mm x 120mm) notepad. Print instructionsCategory: Office Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Doesn't Matter...
prusaprinters
Handy add on to hold a notepadNeed to print and superglue the cover to the platen, and the platen to the clamp.Will require some trimming to get these to fit.UPDATE - added a version that sits horizontally.
thingiverse
i always have a pen (this one is from Pokka Pens) and a sharpie along with a small moleskine notepad ( 3.5x5.5 moleskine ) sitting by my printer. i was sick of them taking up space so i made these. ...they work off small 3m command strips.
thingiverse
It still was easy to tip over, so I took the basic idea and changed it to make it work for various sizes of notepads such as steno pads or letter size pads. I designed one that was wider and longer to keep it from tipping so easy and made the base...
thingiverse
... I just wanted something to hold my sticky notes onto my cubicle wall. ... This is for a 3" x 3" sticky note pad. The magnets are 5/16" in diameter and were installed with the same poles facing one another in the pressure plate and sticky note holder.
thingiverse
It also comes with a handy built-in holder in the base that can store two half-sized pencils (like the kind used by golf players). When you're not using your pencil, you can rest it in the top-mounted pencil-hole for quick access later on. This...
thingiverse
This is a 3x5 card holder to be used with the pegboard shell for the Bambu Lab p1p. ... The left 3d model is for the left hand side of the printer as you face it.
thingiverse
So here is the next monitor storage device, a 3x5 card holder that hangs over the back of my monitor. It can be printed without support if you print it upside down. I made the inside of the base with a large incline to make it easy to grab the...
prusaprinters
So here is the next monitor storage device, a 3x5 card holder that hangs over the back of my monitor. It can be printed without support if you print it upside down. I made the inside of the base with a large incline to make it easy to grab the...
cults3d
To store your notepads and avoid your loose sheets, this file is for you! ... for 90x90 sheets.
thingiverse
I needed a holder for my notepad papers. I bought a refill without a holder so I printed one myself. It has 4 holes in the bottom for faster printing. The size is 90 x 90 x 90 mm. But with the OpenScad file you can changed the size. ...