4 gang outlet cover 3d models
660804 3d models found related to 4 gang outlet cover.thingiverse
electrical outlet cover for a 4-gang box with 4 single outlet round wall plugs
grabcad
I couldn't find a Solidworks drawing/part for a 4 gang outlet cover so I made one! I needed 2 of these face plates for my DIY Christmas lights controller. ...I have NOT tested out the fit/verified the dimensions, I just found them in google images, also...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=731747 Instructions Using the following options: 4th_plate = outlet 5th_plate = none plate_width = 4 2nd_plate_bottom_hole = none 5th_plate_bottom_hole = none plate_size = 0 2nd_plate = outlet...
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
4 gang outlet cover. In case you don't wanna spend $1.89 at your local hardware store... ... But hey any color you want!
thingiverse
Cover for a single duplex outlet in a 2 gang duplex hole remixed from "2 gang outlet cover by cssmacs01".
thingiverse
Simple outlet cover. Use these in my basement. ...Engineered to use little plastic yet very strong.
thingiverse
Remix for a scenario with one GFCI (rectangular) outlet and one duplex outlet. ...This can be printed face-down and the 45 degree chamfer allows printing with no supports.
cults3d
Remix for a scenario with one GFCI (rectangular) outlet and one duplex outlet. ...This can be printed face-down and the 45 degree chamfer allows printing with no supports.
thingiverse
I converted the light sockets to the [4" Circular Outlet](https://amzn.to/2smamzj), but I could not find the cover for purchase anywhere! So this is the result. The cover takes a simple center screw to hold it to the outlet, which should come with...
thingiverse
I noticed that the current one came with tabs on the bottom that made the print well over 6hrs, the other option was print on the side and add supports, tried that and it was not easy to remove supports. ... So I present this remix, tabs taken off and...
thingiverse
Customized version of https://www.thingiverse.com/thing:5336348 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5336348
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
prusaprinters
Use at your own risk of course, and always make sure you know what you're doing with electrical stuff. Note: the screw holes were made to match the 2-gang boxes where the light switches/outlets would normally screw in; not the holes on the switches...
thingiverse
... with electrical stuff. Note: the screw holes were made to match the 2-gang boxes where the light switches/outlets would normally screw in; not the holes on the switches themselves where those plates screw, since there are no switches/outlets here.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=731747 Instructions Using the following options: 4th_plate = outlet 5th_plate = toggle plate_width = 5 2nd_plate_bottom_hole = none 5th_plate_bottom_hole = none plate_size = 0 2nd_plate = outlet...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=731747 Instructions Using the following options: 3rd_plate_bottom_hole = none 1st_plate_bottom_hole = none 1st_plate = outlet plate_size = 0 5th_plate_bottom_hole = none 5th_plate = blank...
thingiverse
Customized version of http://www.thingiverse.com/thing:57647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=57647 Instructions Using the following options: 5th_plate...
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
pinshape
Ceiling Outlet Cover with 3 1/4" holes. ... Shown printed in ABS, but can use filament of your choice.
prusaprinters
2 gang outlet extender 6mm ~(1/4") for extending outlet box when adding tile backsplash or other wall resurfacing. I printed with PLA at .25mm layer height on Prusa Mini.
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956
thingiverse
Customized version of https://www.thingiverse.com/thing:3840723 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3840723