400mm lens 3d models
23219 3d models found related to 400mm lens.thingiverse
Lens cap to replace the massive hood that comes with the lens...
thingiverse
I remixed the mask to support the Panasonic-Leica 100-400mm zoom lens. I also made a change to oversize the fit of the mask, and used small felt pads on the inside of the 3 prongs to better grip the lens hood and not scratch it. Without these pads,...
grabcad
Canon 400mm f5.6 lens with a quick mount bracket from Benro attached to the lens collar.
thingiverse
The old Sigma 400mm lens has an integral hood which can be slid forward to reduce flare. Unfortunately, it is only held in place by Art. Well, that and the velvet-like inner coating on the hood rubbing against the wider part of the lens. As these...
thingiverse
Replacement lens hood for the Lumix (MFT) system Panasonic-Leica 100-400mm zoom lens. Replacement is the same size as the original, and mounts the same way (normal or reversed to stow), except that the clamp has been redesigned to allow for...
thingiverse
Adapting Canon Lens EF 400mm 1:5.6 L (Ultrasonic) for Astronomy with ZWO EAD EAF holder is compatible for [SCT](https://www.thingiverse.com/thing:3992198), [Newton](https://www.thingiverse.com/thing:3992200) or...
prusaprinters
Adapting Canon Lens EF 400mm 1:5.6 L (Ultrasonic) for Astronomy with ZWO EADEAF holder is compatible for SCT, Newton or Refractro telescope.Fine manual focus available too.OpenSCAD source code on GitHubBOM1x Canon Lens EF 400mm 1:5.6 L (Ultrasonic1x...
cults3d
It is a snug fit on my lens, I suggest you cancel a test print to make sure your fits on your lens printing on your printer. Scale slightly as needed. I've been printing out of ABS since it will be out in the sun, and in my car on the road trip out...
thingiverse
It is a snug fit on my lens, I suggest you cancel a test print to make sure your fits on your lens printing on your printer. Scale slightly as needed. I've been printing out of ABS since it will be out in the sun, and in my car on the road trip...
cults3d
Lunar rocket inspired by Mr HERGE's famous comic strip. Designed on Solidworks according to the plan appearing in the album. This 400 mm model is accompanied by a 200 mm and an 800 mm model. This 400 mm model has a motor finally what I imagine to...
thingiverse
Simple lens collar for the Sigma 100-400 lens. Arca swiss plate. Designed in Fusion360. The hinge needs a 5mm rod of almost any material. I've used a piece of carbon fiber but anything with that diameter will work. Make sure it's glued only on the...
prusaprinters
I used ABS but I think PETG would work as well.I will look into designed a front cover for this in the coming weeks.Materials needed:2X M3x12(or 14) screw.6X M3x8(6 might work) flat head screw (flat head not required, just looks better).I designed...
thingiverse
I designed this so you're able to align your film onto a holding ring, and then install that ring inside the lens hood. I highly recommend you TEST this out on something cheap and similar to your solar film. If using the Baader film I'd recommend...
cults3d
I designed this so you're able to align your film onto a holding ring, and then install that ring inside the lens hood. I highly recommend you TEST this out on something cheap and similar to your solar film. If using the Baader film I'd recommend...
cgtrader
It is the quality low-poly 3D model Canon EF 400mm f/2.8L IS II USM Super Telephoto Lens used in various fields 3D Graphics such as: game development, advertising, interior design, motion picture art, visualization, etc.. Modeling was made by...
thingiverse
I originally had the cutouts rounded but found that I could just see the plastic when the lens was at 80mm so I shaved mined down and double checked the values at right around 44mm from the top. The PETG I have is a bit shiny so I'm going to...
thingiverse
I created this lens hood for the Olympus micro four-thirds 100-400mm non-professional lens, which takes an LH-76D hood. If you want to check whether it will fit your lens, the outer diameter of the end of the lens should range between 75-77mm and the...
thingiverse
Replacement part for the plastic plate that goes in the tripod foot of the Panasonic-Leica 100-400mm lens. If the internal tripod foot screws come loose, this part is commonly damaged when removing the plastic trim to access those screws. ...
thingiverse
... x1 + x2 = 400mm calipers. Ive seen 200mm go for over $100.. Remove the end stop tab on your digital calipers (scary!) and slide on a longer ruler. The groove should fit the depth gauge as well. ... One will be added to the design in the future.
thingiverse
Quadcopter frame 400mm Design still in progress.. ...will be updating
thingiverse
Designed by myself BMW Clock with 400mm diameter, 5mm thickness, inner diameter 8mm
thingiverse
monitor light bar, 400mm LED size, printed in 4 parts including the bracket need some double sided tape adhesive for mounting
thingiverse
pp700w moderator using 392mm x 20mm carbon tube, giving 400mm overall barrel length. ... drill a series of 2mm holes around the breach end of tube 10mm from the breach to enable proper sound deadening.
grabcad
400mm drone frame design for 10" proppelers, 25x19mm motor mounting holes. ...Frame is made from machined aluminium, 8mm for arms and 3mm for base.Visit my blog for more projects: http://maj.pavlin.si/
thingiverse
This is a 400mm size version based on the 370mm ver by jason51873 (http://www.thingiverse.com/thing:613877) Original design by tosjduenfs (http://www.thingiverse.com/thing:34552). I think it's more suitable for aerial photography as I intended for.