45 long slide with laser sighting 3d models

There are some of these on the market priced about $100; this can be printed and used with a $5 cat chasing laser, or, you can buy the gun sight lasers for $15 if you want to use it outside. This works with two lasers: 1) Innozon laser pointer...

... head lens tube. ...You will need a 12mm OD laser. The knob is to be bonded to the back of laser diode ( gorilla super glue ) BEST! to allow removing from mount and to turn laser to focus . You will need a 10-32 x 1.5 long nut and screw. ...Enjoy

Remix for the phone slide https://www.thingiverse.com/thing:3312779. The slide arm is directly mounted to the phone holder. ...Supports are required.

LED Mount for 2020 Alu 250 mm long

A long slide that works with the Duplo Legos.

Two scopes mounted on 1911 Style 45 to demonstrate versatility of scope and 45 w/rail for mounting accessories

This is a long slide whistle. ...IT WORKS

This is a long slide lock i have made, it can be used on any door where you want a easy lock. I have made a V2, with smaller screw holes, and made it look more clean. ... -Simon

Extended version of the FNX 45 compensator by Momo_Manbavaran. Added 4 more segments to the end. ... Made in TinkerCad.

Needs 2 M3x25 screws with 2 M3 nuts.

Customized version of https://www.thingiverse.com/thing:2222566 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2222566

LED Mount with slide-in 2020 Alu 340mm long for 10 LEDs with 30 per Meter

This is a rear slide plate for my XDs .45 These plates retain the striker assembly within the slide. These can be swapped out for custom etched versions for a more personalized look. ...I am going to continue working on this to create a type of rear...

Laser mounting / slider. ... Adjusted for AliExpress - Laser Tree, Model LT-40W-F23

Made with .5mm nozzle, Natural ABS, heated bed, 6 row brim, with supports on a Vision Printer. Base has mounting holes that need opened up as needed to screw under a shelf. The slider has a four hole pattern that needs opened up and with longer 6-32...

The driver used can be found at site noted.http://jtechphotonics.com/?product=2-0-amp-adjustable-laser-diode-driver-kit-8v-compliance Instructions Made with .5mm nozzle, Natural ABS, heated bed, 6 row brim, with supports on a Vision Printer. Base has...

Need to release my laserpointers sometimes Using more then 2 lasers But switched ON So a slider. Diameter pointers 13.25. ...mm.

longer by 17.5mm and fit laser with diameter 32.5mm

Model dimensions: - length – 267 mm - height – 181 mm - width – 38.4 mm Model consists of parts: barrel, body part 1,2, bottom plate, front insert, front plate, front sight, hammer, hub, inner pin 1,2, left grip, rear insert 1,2, rear sight, right...

Barn Door slide track. ... See the pictures for dimensions. Taller than slide track that comes included with most barn door kits. ...(if not all of them)

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_height = 4 nut_thread_outer_diameter = 9 type = bolt nut_height = 6 head_type = hex nut_thread_step = 2 outer_diameter = 14 thickness = 2...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=114369 Instructions Using the following options: gripLen = 120 thickness = 2 gripAngle = 45 gripDia = 8 sink = 1.5 volume = 14.7868 MINITESTGRIP =

Model dimensions: - length – 267 mm - height – 137.5 mm - width – 34.5 mm Model consists of parts: barrel, body part 1,2, bottom plate, front insert, front plate, front sight, hammer, inner pin 1,2, left grip, rear insert 1, rear insert 2, rear...

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

<3 Updates 20220702: Added another drawer with hole Version Infos - Drawer_V2: tollerances adjusted - Container_V4: Higher plattform to decrease stress on the cable (bending) License - PLEASE READ This design is under copyright. This files are ONLY...

A simple remix.

Update:Added sights in 1911_slide_with_sights.stl.The old stl file I uploaded called 1911_slide.stl has a fatal defect -&gt; there is no space for ejector, I fixed this problem in 1911_slide_with_sights.stl. ...(1911_slide.stl is already deleted)If you...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/cAMYv5ptIOA

Spring Diameter 45 mm, 211 Long

IGUS RJ style slide bearing 57mm long (use as single slide in Prusa style carriages), I widened the spacing from my original slide design. ...Suggest to print in PLA first to get a good fit before using IGUS filament because it's really expensive,...