4x18650 3d models
45 3d models found related to 4x18650.thingiverse
Customized version of https://www.thingiverse.com/thing:3555258 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3555258
thingiverse
Copter on 4x18650 Motors 2205- 1600kv-2000kv for 2s2p config Props 8x38 ATG frame - 70g ABS - 25% infil All parts glued with acetone 30min+ on flight
thingiverse
4х18650 battery container for installation in equipment. It is necessary to be used with a standard Chinese container. ...It is necessary to solder four brass plates.
thingiverse
Customized version of https://www.thingiverse.com/thing:57281 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=57281
thingiverse
I use it as a powerbank for T12 soldering irons. 4 x 18650, 16.8V Due to the height, use a minimum 10mm brim. ...
thingiverse
Initially I purchased cheap 4x18650 holder, but as you can see on one of photo, after full load of cells, it start cracking. The metal connectors are too stiff and holder plastic too weak. So I recreated better holder, in principle is the same...
thingiverse
Battery holder for 4 li-ion batteries of 18650 type. you can connect the batteries in the following options: 2 parallel, 2 serial 4 serial 2 serial, 2 parallel. I used copper sheet for the contactors. I made it for my RC boat and connected it 2Px2S...
thingiverse
Customized version of http://www.thingiverse.com/thing:1524661 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1524661 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:57281 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=57281
thingiverse
Customized version of http://www.thingiverse.com/thing:57281 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=57281
myminifactory
A simple case for holding four 18650 batteries that opens below the batteries for easy access and has slots for 6mmx2mm neodymium magnets to prevent the case from opening in a bag or pocket. Features Holds up to four 18650 batteries Reversible cap...
thingiverse
Customized version of https://www.thingiverse.com/thing:57281 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=57281
thingiverse
- Simple case for DIY powerbank - You'll need 4*18650 lipo battery - you can get them from an old notebook battery or buy them from ebay/aliexpress - And one of these modules shown on the 5th picture (I use 5V 2.1A one - supports fast charge) - I...
thingiverse
Customized version of https://www.thingiverse.com/thing:1351565 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1351565
thingiverse
This is design for 4 18650 batterys and make batterys visible. I tested it. It is too tight. ...Try 110% to get a little loose
thingiverse
My first design with Fusion360. Using 4 neodym magnets (8mm diameter, 3mm thick) to make the top snapping into place. There are two different versions of the case. One with magnets visible so they can be inserted after print. Maybe they have to...
thingiverse
Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291
thingiverse
Bicycle light Battery pack (4x18650) protections and fixing (using velcro straps). ... Desgned sith DesignSpark Mechanical (file included).
thingiverse
Holder for bike frame 6800mAh 8.4V 4X18650 Battery Pack For Bicycle light
thingiverse
Simple Flashlight stand for 2x Ultrafire Cree with Battery (2x14500 and 4x18650) storage.
cults3d
Power bank (4x18650) Designed for this board:"https://aliexpress.ru/item/32742598051.html?spm=a2g0s.9042311.0.0.725233ediRjvdD"
thingiverse
Power bank (4x18650) Designed for this board:"https://aliexpress.ru/item/32742598051.html?spm=a2g0s.9042311.0.0.725233ediRjvdD"
thingiverse
Прокачай свій фонарик безплатними акумуляторами з одноразок! ... Make your own capacity upgrade to keychain flashlight! 9x13300,13400,13450 or 4x18650 battery required for this mod. ...
thingiverse
Not exactly sure if this is going to work or not. ...Made for 4x18650 Li-Ion Batteries. Needs a dummy battery and adapter from a wall adapter. ...Tutorial will be coming soon.
thingiverse
... bottoms so you can sort your own electronics ouit. https://www.ebay.co.uk/itm/TOMO-M4-DIY-Smart-Power-Bank-Case-Box-4x18650-Battery-Dual-Output-USB-Char-TDMFS/402521004686?ssPageName=STRK%3AMEBIDX%3AIT&var=672750920533&_trksid=p2060353.m2749.l2649
thingiverse
This is a battery holder for 4x18650's that can mount to the side of a Corsair HS70. 4 battery's is a bit to heavy to have hanging off your right ear cup, but hey that is what I did. ...I would recommend that if you attempt this, that you use 2 battery...