4x5 camera 3d models
108655 3d models found related to 4x5 camera.thingiverse
This 4x5 camera is designed for ultra slow film and photo paper. Some parts are still being refined and tested. Will upload once I am satisfied. ... Required materials that cannot be printed: -4x 8mm, 200mm long, metal (any metal) rods -8x M5, 60mm...
thingiverse
More details on the use of the adapter: http://www.nycresistor.com/2012/03/11/4x5-view-camera/ Instructions Cut from 5.5mm acrylic; otherwise the size of the holes and tenons will not work. ... Secure to the view camera frame with cotter pins and mount...
prusaprinters
Fas forward to a 6 years ago I found https://jongrepstad.com/building-a-large-format-camera/ and decied to give it a go. I built all of the parts except the the sliders, the project was shelved due to a job change.</p> <p>I like the plans, and the...
thingiverse
Fas forward to a 6 years ago I found https://jongrepstad.com/building-a-large-format-camera/ and decied to give it a go. I built all of the parts except the the sliders, the project was shelved due to a job change. I like the plans, and the ease of...
thingiverse
This is a magnifying focusing hood for Intrepid 4x5 cameras. It snaps onto the ground glass back at the top and bottom using clips that can be replaced as they wear or if you break them. The lens used is a 150mm plano-convex lens, which should...
thingiverse
The 6x9 frame is centered both vertically and horizontally within the 4x5 camera's rear standard. Note that because the frame counter shows the 645 frames (not the 6x9 frames), you'll want to expose on frames 1, 3, 5, 7, 9, 11, 13, and 15 to avoid...
thingiverse
An alternative grip for the [WillTravel camera](https://www.thingiverse.com/thing:4084731). Different to hold and building a little less in width compared to the original. You need four M3 30mm Hex Socket Head Cap Screws or similar to attach to the...
thingiverse
Lens box holder for Graflex Speed Graphic 4X5 camera
prusaprinters
These lens boards fit a Linhof Kardan Standard monorail 4"x5" cameraLens board for a Copal #0 shutter (34,6mm - hole diameter is 0,2mm oversize)Lens board for a Copal #1 shutter (41,6mm - hole diameter is 0,2mm oversize)Lens board for a Copal #3...
thingiverse
Available at Shapeways in laser-sintered nylon:https://www.shapeways.com/model/1327840/pinh5ad-the-3d-printed-4x5-pinhole-camera.html?li=shop-results&materialId=25 ATTENTION This work is licensed under the Creative Commons - Attribution -...
thingiverse
This is a small utility that shortens the available flange to lens distance for the Intrepid 4x5 camera. So that you can use wide angle lenses with a focal length shorter than 80 mm. I've successfully use the Schneider Super Angulon 47mm with a...
thingiverse
A small extra for the [Will Travel 4x5 camera ](https://www.thingiverse.com/thing:4084731/files). If you are using the focus screen holder *WillTravel4x5-GLASSGroundglass_topbungee_v4* for your camera you can use these holders to hold the glass in...
thingiverse
--- --- --- --- --- --- --- --- Inspired by Morten Kolve's "Will Travel 4x5 camera", I decided to try and design my own, since I had a 75mm lens and fotoman helica focus to use. This is a work in progress. I uploaded the 123D design save files as...
prusaprinters
Added hotshoe mount (M3 nuts and bolts) and simple hotshoe, might be a bit shallow. Added grip mount, (M4 nuts and bolts), should fit the Goodman Zone camera grip. Added 3/8" screw tripod mount under middle section. Inspired by Morten Kolve's "Will...
thingiverse
I have been thinking about a super wide 4X5 camera for a long time and I'm happy to finally publish this in time for Worldwide Pinhole Photography Day, 2016! This camera's pinhole placement (and subsequent perspective) is designed to be easily...
thingiverse
This is a simple 4x5 sheet film pinhole camera. Intended to learn how to drive tinkercad. ... Focal length: 90mm Pinhole dia: 0.4mm F-stop: f255 Angle Of View: 84.2 Deg
thingiverse
After wasting so many 4x5 film sheets from missing critical focus, I decided to work with a friend of mind in a 3D Facebook group to design this focusing hood and it has worked wonders. It allows you to focus even hand-held (which I do not recommend...
thingiverse
Here is a hopefully useful add on to Morten Kolve's ( https://www.thingiverse.com/mortenkolve/designs ) amazing WillTravel 4x5 camera. A loupe attachment for the ground glass. This works great in tandem with a viewfinder (Morten's 3d printed...
thingiverse
This is a lens board for a Graphex 135mm f/4.7 lens to fit the 4x5 Intrepid Camera.
thingiverse
Specs: - "double" focusing mechanism for both lens and film frames with anti backlash - smooth movements on double 8mm rod rail using SC8UU linear ball bearings - back frame - fixed in z-axis, +-10 degrees tilt - front frame - moved in all directions...
thingiverse
Flat lens board for MPP Mk VIII 4x5 view camera. I use it with a Schneider Super Angulon 75mm 1:8. The lens board must be removed when closing the camera. ... Instructions Print in black ABS or PLA
thingiverse
Coned lens board for MPP Mk VIII 4x5 view camera. Must be printed with support on FDM printers. I use it with a Schneider Super Angulon 90mm 1:6.8. The lens board must be removed when closing the camera. ...
thingiverse
Could be used with 4x5" cameras with graflock back (LH4x5_GraflockBase.stl), or as conversion for Magnifax 4 enlarger (LH4x5_Magnifax4Base.stl - or any other enlarger if you glue it in some way ;-) ). As light source can be used power LEDs: 4x...
prusaprinters
While on my search for a 4x5 camera, I realized that it is generally economically inaccessible to a wide audience, because of how costly a camera can be. This camera intends to open up large format photography to a larger audience, this...
thingiverse
Bits and bobs to turn the pieces of a Sinar X standards into a functional camera again.
thingiverse
The aluminum base of the Intrepid 4x5 MkIV field camera is 4mm thick while the the typical tripod mounting screw on most tripods is well over 5 mm long. Because of this design flaw, when you attach the camera base to just about any mount, the screw...
thingiverse
This is a replacement back for a Polaroid pack film camera that allows it to shoot 4x5 negatives using the included custom film holder which is only 106mm wide, so that this film back will fit onto the back of the camera flush. Remove the hinge...
thingiverse
... lens is quite clear. So I have remixed a 4x5 film back to, hopefully, work with this camera. I cant imagine anyone else would need this, but Im posting it here anyway. It will be neat if this works. This is very much a work in progress... ...
thingiverse
Tested with the Polaroid landcamera, Fujifilm FP-1 and the 4x5 camera as well. ... check my channel for further updates: https://youtu.be/OmdPPszZT84 https://youtu.be/EfTuYYhVzko https://youtu.be/u3iH1e8EJUA www.youtube.com/c/KeigoMoriyama ...
thingiverse
The PINH5AD is a large format pinhole camera I designed to work with a 4X5 sheet film holder. This frame replaces the film holder for the purpose of visualizing the (inverted and rotated) image formed through the pinhole. Because the image will be...