4x8 1 2 osb 3d models

They are connected in 1 pendant tightly, they can be kept on one chain. It is a remix of Ablapo's Yin Yang Necklace, but I could not to set it ( Print dot and prot files first in one color, second in another color. I used white PLA and black...

The prime link 8_2_1 model, displayed within a constant-radius tube and pulled taut, can be found in both thin and thick versions on this website. The thinner version's tube has been reduced to half its size for improved visibility of crossings. For...

Schraubstockversion 2.1 Befestigungspunkte auf Arbeitsplatte: 50x50mm (M4) A250 - beide Grundkörper sind identisch und können mit VierkantMuttern (M6) bestückt werden. Die Einlässe dafür sind durchgängig so dass die Muttern einfach ersetzt werden...

1/2" Pex outer diameter is about 15.8mm so there is .2mm of room to work with. The fit is snug and no glue or anything is needed to secure the pex in place. ... Printed this coupler standing upright with supports Other Pex parts: 90 degree Elbow...

1/2" & 3/4" bearing rollers are interchangeable. On March 13, 2016: A bushing for 1/2" PVC was added. This allows the use of a 3/8" bolt. Just cut PVC to the correct size. A lathe will true the ends and dial in the width. Full instructions can be...

Llantas coche rc 1:10

Hello, this is my first design made to place 1/2 inch aluminum tubes in wooden boards, chipboard, drywall, etc. The support is quite simple and easy to print. It can be fixed with 3.5mm thick screws. I've added another slightly larger design if...

1/2" (half inch) stopper for blocking wall sockets while carrying out new installation work or emergencies or in general. Will post picture once I print and test out. Second version made which doesnt print support around thread. Recommend...

When crafting rain barrels, I encountered leakage issues around 1/2-inch NPT fittings (despite being threaded and sealed) as temperatures rose with sun exposure. I concluded that the thin walls of the barrels were insufficient to maintain a tight...

... eyes are cast downward, and their facial expression is neutral. The second photograph, labeled "Portrait 2," features a different individual. ...This person's face is turned straight forward, and they appear to be looking directly at the camera.

This is a Fin for the Floss 2.1, giving credit where it's due to Serge for conceiving the ingenious idea of utilizing leftover zip ties to secure the component. The fin features a hook that expertly captures the front segment of the top plate and...

These are Wrecks 1 and 2, two of the three discovered in Gothenburg and unearthed in 2019. The wrecks date to the late 17th century, built as small clinker cargo vessels that transported goods from larger ships into the town. They were deliberately...

These are 1/2"-13 thread with a slotted head. The thread is a Class 5 which is tighter than a normal thread. I initially made these to seal the empty holes on my Kurt milling machine vise, but the possibilities are endless. ...Can create size to suit...

This sturdy bracket attaches directly to the outside of a shelf or box, perfectly suited to hold a standard 1/2-inch PVC pipe in place. ...The carefully crafted mounting holes are specifically designed for 3/16 bolts, ensuring a secure and stable setup.

We've got a deal-maker on our hands with this sleek 2-in-1 phone stand. Take a gander at the phone in action - it's an iPhone X that's turning heads. One of the standout features is the adjustable angle setting, giving you full control over how your...

Here are the specifications for custom-made blowgun darts: 36 units will be produced with an ID of 1/2 inch and a .125 inch hole to accommodate 10-inch bamboo shafts, utilizing a 15% infill for optimal lightweight construction. If they fit snugly at...

... to print one out yourself, I'd love to see a photo of it. This customized piece shares the same length as standard track, allowing it to fit seamlessly with existing pieces like Funnel 3:2 (available at https://www.thingiverse.com/thing:2696610).

... https://www.thingiverse.com/thing:4045482. I needed an NPT adapter specifically designed to adapt from 2 inches down to 1.5 inches for an old projector mount, but it's worth noting that this design is not intended for use in plumbing applications.

You can mount your iPad 1 or 2 on the wall using a FHEM heating control setup with ease. To take out the iPad from its holder, simply push it upwards and remove it. To create this mounting system, I use Loom Bands - specifically the green ones -...

Suppressor for standard 1/2-28 UNEF threads. 22 Long rifle only!!!! Warning! I have not testet this design! Do not use supports! You will fill the internals of the model!! It is required to have good part cooling because of the internal...

I needed a mount for 1/2" wooden dowels to hang my plant lights which was also minimal and small form factor. This, with a single screw does the trick.Print in whatever material you like. As long as you aren't hanging a lot of weight. I printed mine...

This is a Fin for the Floss 2.1. I want to give credit to Serge for the great idea about using left over zip tie to secure the part. This fin has a hook that catches the front part of the top plate and tabs that helps catch the center part of the top...

... specifications for this unique item include a text thickness of 4, 25 sections, a length of 15, with holes included. Its outer radius is set to 33 and its inner radius is 28. The nozzle size used was 0.4, while the text on it reads "NYC 1/2 2014".

This custom piece was specifically designed to fit a one-of-a-kind situation where the elbow fitting pokes through the wall (as shown in the image), The flange features a recess of 7/16 inches to accommodate this unique protrusion.\r\n\r\n\r\nTwo...

I made some brackets specifically designed for holding 3/4 inch wood pieces together using 1/2 inch wood screws, which measure 19 inches wide. They've proven to be very useful in my current project, although it's uncertain whether they'll be of any...

Turning 1/2" sockets by hand before using a wrench provides more torque than holding the socket in your hand. This design prints without a brim because of its circular bottom. A high infill percentage is used to prevent torsional failure when the...

Remixed Jeebo PCB Holder 1.2 with tray: - grip helper II. (screws and nuts: 2x M3x12 + 1x M3x18 + 2x M3), - M3 inserts in grip helper I. (for attaching grip helper II.), - bigger holes in L/R base for fixing 12 mm rod with 3D printed knob (for...

Suppressor for standard 1/2-20 UNF threads. 22 Long rifle only!!!! Warning! I have testet this design with a few shot and it works! Do not use supports! You will fill the internals of the model!! It is required to have good part cooling...

UPDATE: I order to create a wreck, i add 3 new STL files: fork without wheel wheel alone side wheels without cat To make a "wrecked" version, I added 3 STL files: the fork without wheel front wheel sprocket and wheels without chain Hi, This is 3d...

Brass union tee with 3X 1/2" push to connect fittings. Parker p/n 164PMT-8 or Grainger item# 11K696. ...Max pressure 250 psi