5 1 4 bay fan 3d models
1389087 3d models found related to 5 1 4 bay fan.thingiverse
I was keeping both my SSDs for my server in the bottom of the case when I suddenly thought about a way to install them in the now-useless 5 1/4 bay at the top of my case. Quick run into Fusion 360, and here we go! This holds 2 SSD side-by-side,...
thingiverse
I made a storage bin that fits into the 5 1/4" bay. This allows you to put 5 SD cards, and 5 Micro SD cards in the bin. Also has room for CD/DVD (system recovery stuff), or you could even put in a USB harddrive (I put in my Western Digital Passport...
thingiverse
Holds 3 x 2.5" SSD drives in place of a 5.25" optical drive. Recommend using a couple of M3 screws to secure it to the chassis. There are no screw holes to hold in the drives, instead, the width of the slots for the drives is slightly reduced...
thingiverse
Holds your phone/table on the front of your pc. ...Kinda flimsy lmao. Space the holder part off with washers if the bay mount doesn't sit flush with the front of your case. ...Use m3 nuts/bolts.
pinshape
... PLA for caddy. PLA or ABS for front panels. Allowance for front panels is calculated for 0.4 mm nozzle. Front panels are loose, if You use 0,3 mm nozzle(have to glue them to the caddy base) and probably hard to slide, if printed with 0,5 mm.
thingiverse
Print Settings Printer: TRENDi Maker V3 Rafts: No Supports: No Resolution: 0.2 Infill: 10-15% Notes: Allowances for front panels(sliding them in place) are OK with 0,4 mm nozzle. ...It`s loose for 0,3 mm nozzle and probably hard to fit, if using 0,5 mm...
thingiverse
Based on this excellent 80mm fan mount: [PC front cover 80mm fan front double height 5.25 inch](https://grabcad.com/library/pc-front-cover-80mm-fan-front-double-height-5-25-inch-1) I modified it for better fit to my drive bays, and since PLA isn’t...
prusaprinters
Essentially, you can turn a single 5.25" bay into up to 4 of the highest performance 2.5" HDDs or SSDs for all your NAS needs by using any of your old and useless cases.Looking around, this also seems to be a very high density package, as 3 5.25"...
thingiverse
Fits into four 5.25" drive bay slots, has mounting holes for 140mm and 120mm Fans. ... Optional square vent grill also available, but might re-make this for better mounting, so I don't recommend printing it, as it WILL fail at some point
thingiverse
... to mount my hard disk next to the CDROM drive, as the power cable was too short. ... So I designed this item and it works perfectly. Print as is, no support needed Use 4 M3x10 screws to mount hard disk. ...Use Wood skrews to mount tray into bay.
thingiverse
... above the HDD. I modeled it to use fan screws for securing the fan and for securing the Pi/HDD carrier to the fan body. It will also work fine without a SSD/HDD. ... Update 20 November 2019: Added a fan shroud (inspired by TheMonkeyStink's make).
thingiverse
This a cooler cover to attach a fan for the Sabrent 4 bay HDD dock
thingiverse
Simple and effective 3x 5.25 12cm Fan Bay for better PC refrigeration. ...
thingiverse
Made for cases with two, or more, 5.25" bays. You can mount two standard 70x70mm fans. It's mounted to the case using 4 or 8 M3 screws. The measurement were used from provided pictures found on the internet. NOTICE!!!: The height of 85mm might...
thingiverse
This allows you to suck/blow air out a front bay using a 120mm. ... two versions are avaliable, Fan above bay or fan below bay.
thingiverse
Simple 120mm fan mount which fits my Sabrent 4 bay HDD docking station. The HDDs run very hot without some sort of fan, so I designed this fan mount to simply sit on top of the drives. The inner dimensions which encase the drives are 122x102. You...
thingiverse
I only had two 5.25" bays free and a spare 120mm fan from an old power supply so I came up with this design. Running at 7v it pulls quite a lot of air into the case and is fairly silent. Screw two vents one to either side of a 120mm fan and use four...
cults3d
I only had two 5.25" bays free and a spare 120mm fan from an old power supply so I came up with this design. Running at 7v it pulls quite a lot of air into the case and is fairly silent. Screw two vents one to either side of a 120mm fan and use...
thingiverse
this is a 3 part design, very simplistic in nature but effective in execution (if I do say so myself) it uses the two 5.25 bays typically only available in a mid-atx case and positions the 120mm fan at a angle suitable to fit but still flow air...
myminifactory
5.25" Drive Bay Fan Cover for 120mm Case Fan
thingiverse
If you want add 4 more hdd to your dell t320 under the optical drive you can use this model
prusaprinters
... as well as to mount to the back panel. I've included a template to mark the holes that need drilled/cut.If you want to have the fans centered you can use this spool holder: https://www.prusaprinters.org/prints/151511-voron-v01-offset-spool-holder
thingiverse
This is remix of https://www.thingiverse.com/thing:1860960 fan support. ... Fan 80x80x15 also works perfect.
thingiverse
A mount for a custom computer fan speed PWM controller. ... A knob for a potentiometer to adjust the fan speed. Fits into a standard 5.25" drive bay.
thingiverse
A 140mm fan Holder for 5.25 PC bay. Distance beetwen holes 124.5mm. 4mm holes for fan screws. Side screws 2mm, You can use a ABC screw or try with PC ones. No threads in the holes, you can do it if neccesary with a thread maker. You need 4 free...
prusaprinters
This is remix of https://www.thingiverse.com/thing:1860960 fan support. Fan 80x80x15 also works perfect. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: 0.2 Infill: 10 Notes: Sunhokey Prusa i4...