5 16 bearing 3d models
688921 3d models found related to 5 16 bearing.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=991714 Instructions Using the following options: bearing_resolution = 50 height = 5 bearing_tolerance = 0.125 inner_radius = 5 bearing_support = 2 bearing_radius = 3 ring_fillet = 2.5 width = 16...
thingiverse
I based my design off of http://www.thingiverse.com/thing:18219 by KR2. ...The original was meant to fit an 8mm sized rod but I have found that Home Depot sells 5/16 rods that are considerably cheaper than any 8mm rods I have found online.
thingiverse
I have been using 5/16 smooth rod instead of 8mm, with very good results, because it is cheaper and easier to find, since many machines are designed for LM8UU linear bearings I took [mightynozzle design](https://www.thingiverse.com/thing:2202854) and...
thingiverse
Customized version of http://www.thingiverse.com/thing:2044157 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2044157
thingiverse
Cyclone PCB Factory STLs are published for not so well calibrated machine so when you put LM8UU they fit too loose so I used https://www.thingiverse.com/thing:2202854 to compensate, also I'm using 5/16 smooth bar since it is a lot cheaper.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_type = normal thread_step = 2 nut_thread_outer_diameter = 9 texture = exclude slot_width = 1 thread_length = 25 inner_diameter = 8.1...
thingiverse
... with 2 generic M3 screws (20mm length). The base can be mounted on your project with any M4 screw! Other sizes on my account! Enjoy! (ball bearings and screws not included) Instructions Just print it, put the ball bearing in and screw tight!
thingiverse
Customized version of https://www.thingiverse.com/thing:1525769 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1525769
thingiverse
Customized version of https://www.thingiverse.com/thing:2437268 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2437268
thingiverse
This is a thin case for 1685 ball bearings, very useful in all of your DIY builds! ... Enjoy!
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: number_of_planets = 5 nTwist = 1 approximate_number_of_teeth_on_sun = 9 number_of_teeth_on_planets = 6 tol = 0.4 w = 8 P = 45 T = 15 D = 50
thingiverse
This Linear Bearing was designed for a 5/16 inch chrome plated rod. Some of the chrome plated rods that you can find at a local hardware store can be fairly smooth over a certain distance. PLA is a fairly hard plastic and can slide pretty well over...
thingiverse
Customized version of http://www.thingiverse.com/thing:2183228 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2183228
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options: wall_thickness_c = 2 wall_thickness_v = 3.5 wall_thickness_h = 2.5 min_length_h = 40 shaft_diameter_v = 13 shaft_diameter_h = 8 cradle_height = 5
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options: min_length_h = 40 cradle_height = 5 shaft_diameter_v = 13 shaft_diameter_h = 8 wall_thickness_c = 2 wall_thickness_v = 3.5 wall_thickness_h = 2.5
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: number_of_teeth_on_planets = 6 approximate_number_of_teeth_on_sun = 9 tol = 0.15 nTwist = 1 number_of_planets = 5 w = 8.2 P = 45 T = 15 D = 50
cults3d
... used on most printers. They use the same M3 screws as before, but uses one M2x8 mm screw for the smaller bearing. I'm using these now on my Prusa and it's smooth, quiet and completely slop free.Bearing block for 8mm (or 5/16") shafts/round rails
thingiverse
Bearing-01-4mm.stl Slightly tighter grip on the rod and using one 2x6x3 mm bearing to the one closest to the mounting face, so that it doesn't build higher than the standard bearing blocks used on most printers. They use the same M3 screws as before,...
thingiverse
I have modified this to fit with 5/16 inch threaded rod.
thingiverse
... bushing.scad into box_frame folder (overwrite). Modify box_frame/configuration.scad: // [rod_radius, outer_radius, height, type (2 for combined), hint] my_bearing = [4, 7.7, 24, 2, "lm8uu combined bushing/bearing by ksa"]; bushing_xy = my_bearing;
thingiverse
Customized version of http://www.thingiverse.com/thing:2044157 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2044157
thingiverse
Customized version of http://www.thingiverse.com/thing:2044157 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2044157
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=82067 Instructions Using the following options: Tool_Height = 2.5 message = Font = write/Letters.dxf Tool_Length = 4 $fs = 0.1 Nut_Size = 16.5 Has_holding_cap = 1
thingiverse
This is the gooseneck bearing for a Hobie 16 Catamaran. It needs a stainless 3 inch screw to connect the top and bottom. ... Allows for easier downhaul adjustment, prevents the boom from getting hung up in the mast track, and protects the mast.
grabcad
Igubal 16mm flange bearing with 2 mounting holes For more information and dimensions see http://www.igus.co.uk/wpck/default.aspx?PageNr=2488&wt.mc_id=grabcad
grabcad
Igubal 15mm flange bearing with 4 mounting holes For more information and dimensions see http://www.igus.co.uk/wpck/default.aspx?PageNr=2489&wt.mc_id=grabcad