5 16 bolt 3d models

This is a knob that a 5/16" bolt can be pressed through and used for a tension knob.

The knob requires a 5/16 bolt (both times I've used a 2 inch bolt for the stands I've repaired). The tolerances are intentionally tight. ...After printing the model the bolt is screwed into the knob most of the way and then the hex head of the bolt...

The knob requires a 5/16 bolt (both times I've used a 2 inch bolt for the stands I've repaired).The tolerances are intentionally tight. After printing the model the bolt is screwed into the knob most of the way and then the hex head of the bolt is...

http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_sides = 6 supportless_friendly = 1 screw_hole_length = 100 knurled_strong = 5 knurled_height = 70 height = 14 nut_thickness = 5.23 diameter_2...

Customized version of https://www.thingiverse.com/thing:1562501 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1562501

Customized version of https://www.thingiverse.com/thing:5408177 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5408177

Wall Mount to 5/16 x 3" Bolt Was used to mount a monitor that used a 5/16 to VESA conversion. ... In the build, I used 5/16 - 18" x 3" bolt with nut.

I made this for some quick clamps I have for my wood working tools. ...The bolt snaps right in with some force so no need to hold on to it when installing. It’s for a 5/16” standard hex bolt.

... Craftsman came with, so I made this one. ...Fits on a 15/16" shaft and mounts on the end with a 5/8"-16 bolt (the threaded hole was already there). Hopefully it doesn't break :P Might re-make the spokes in steel if it does. ...Works fine so far.

Customized version of https://www.thingiverse.com/thing:5408177 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5408177

Made it bigger. ... Customized version of https://www.thingiverse.com/thing:904784

Woodworking featherboard for use on the tablesaw or band saw. ... Designed for use with 5/16-18 bolts for T-track or miter slot. ... Inspired by thing 1795001

I used this to replace the a few that broke off of my boat awning. I printed this with ABS and it works great. Instructions Simply print and enjoy. I suggest rotating it about the x axis 180...

I was inspired by the low-profile step-blocks by UltiArjan here https://www.thingiverse.com/thing:1744734 but re-designed these from scratch in Fusion 360 to accept 1/4" and 5/16" bolts, There are two versions of the step-block. One for a range of...

This is a bolt and nut with 5/16-18 threads. Also included a single thread for the OD thread and the ID thread so anyone can make whatever thread length they want to. These threads are not made to exact machined thread tolerences as thats not enough...

Two blocks in this file, both are zinc finish: 5/16" Hex Nut, 18 TPI 5/16" x 2" Hex Cap Screw, 18 TPIThese include 2D center-line and nodes at connection points on separate layers for easy assembly.These are near ANSI spec but zero tolerance,...

This knob for hand tightening 5/16" hex head bolts used in jigs.

http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_sides = 6 knurled_density = 50 cross_section = 0 nut_thickness = 5.5 knurled_strong = 5 nut_width = 12.5 bottom_thickness = 0.6 diameter_2 =...

A simple 7.5mm / 5/15" / .3" nut for a machine screw with OD of 13mm Print Settings Printer: DIY Mendel90 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .2mm Infill: 25% How I Designed This Used OnShape to create this

Customized version of https://www.thingiverse.com/thing:1750904 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1750904

8 Inch - T-Track for 5/16 T Bolts. You know a basic T-Track. 3/4 in. width 3/8 in. depth 3/8 in. ** This is a test to be used for a table saw crosscut sled. ... T Bolts:...

Original Design: https://www.thingiverse.com/thing:3114139/files You will need: 1) 5/16"x6" Bolt 1) 5/16" Nylock Nut 2) 1/4" Washers (yes, 1/4") The washers go inside the bushing, then the bushing goes inside the pockets which the bearings would...

Customized version of https://www.thingiverse.com/thing:713300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=713300

I was going to order a new foot then realized a spare 5/16" bolt would fit. ...I was about to install it bare but then thought I don't want to forget about it and scratch the floor later so why not finally 3D print something that is actually useful :)

Lag Bolt 5/16 x 3.5" and me

Engranaje grande del extrusor compatible con hobbed bolt de 5/16 para impresoras prusa i3

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_height = 5 resolution = 0.2 thread_step = 1.411 nut_type = normal slot_depth = 2 step_shape_degrees = 45 thread_length = 19.05 facets = 6...

I didn't have a bolt to use but wanted to try the stabilizer out, so I printed one. There are two versions, one has a V cut out of it to make it easier to extract in the event it were to take a bad fall and break. ... I recommend printing in 100%...

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

... holding a large PCB. I'm also using 1/8 inch smooth rod in place of the M4 smooth rod. It fits just fine into the existing holes without modification. Instructions Print, push 5/16 inch carriage bolt through square hole, secure with 5/16 inch nut.