5 16 shaft coupler 3d models
646386 3d models found related to 5 16 shaft coupler.
thingiverse
An extended replacement coupler for a 5/16 shaft to 5/16 shaft. ... M3 socket head and M3 nut (x3)
thingiverse
5/16" shaft with 5 mm flat to 1/4" shaft coupler This has extra length on the 1/4" shaft to accommodate more contact area (and to prevent slippage. Used 3X M3 cap head screws and 3X M3 nuts. The solidworks model is not more "parametric" in that...
thingiverse
A 5/15" shaft w/ 5 mm flat to 5/16 round shaft utilizing M3 nuts and setscrews (x2) Note fitted to a Perfomax Drum Sander I'm fixing to sell for a scout troop. ...
grabcad
Rigid shaft coupler for coupler a NEMA17 stepper to a 8 mm lead screw.
thingiverse
Customized version of https://www.thingiverse.com/thing:964680 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=964680
thingiverse
5/16" threaded rod to 5mm motor shaft. Print 2 pieces per motor and assemble with M3 screws and nuts. ...I made these to eliminate Z-wobble on my Prusa-Mendel variant printer.
thingiverse
It's a fast edited coupler. ... D1: 5mm (For NEMA17) D2: 8mm (For shaft or threaded rod)
thingiverse
... Notes: Printed great. The coupler slid in beautifully when it paused on layer 34 and had good clearance for the nozzle when resumed. ...Post-Printing How I Designed This Designed with 123D Design
grabcad
Editable shaft coupler. With the current outer diameter it can connect any combination of shafts of up to 23mm diameter. ...Part1.SLDPRT has the configurations of both aluminum parts.
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=1101036 Instructions Using the following options: set_screw_dia = 3. coupler_height = 30 shaft1_dia = 5.1 coupler_dia = 20 shaft2_dia = 8.1
thingiverse
This part couples two different sized shafts (16mm, 9.5mm) with flats for driving a parker ball valve using a Zebra tech hydro wiper. ...Print Settings Printer Brand: MakerBot ...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_nut_depth = 2.7 pulley_b_dia = 20 m3_nut_flats = 5.7 nut_angle = 90 teeth = 16 nut_shaft_distance = 1.2 retainer_ht = 1.5 m3_nut_hex = 1...
thingiverse
Customized version of https://www.thingiverse.com/thing:964680 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=964680
grabcad
Flexible spider shaft coupler with a diameter 5 and 8 millimeter suitable for NEMA17.
thingiverse
... Craftsman came with, so I made this one. ...Fits on a 15/16" shaft and mounts on the end with a 5/8"-16 bolt (the threaded hole was already there). Hopefully it doesn't break :P Might re-make the spokes in steel if it does. ...Works fine so far.
thingiverse
Couples a Denso Window Motor to a .5 inch keyed shaft with no nonsense. Instructions Shouldn't need support. ...Print solid.
thingiverse
This part fit to the Stepper Motor NEMA17 shaft with a 5.0mm diameter. There are 3 of M4 holes at the top with the position of 120 degree with each other hole. ... There are 3 of side screw holes with M3 size to tighten the part and shaft.
prusaprinters
A print that allows connection of a 2.5mm motor shaft to a 6mm hex. This was built to allow motor to coupling with the the following Thingiverse worm gear: https://www.thingiverse.com/thing:3079719 Print instructionsAdd a 3mm nut and bolt to allow...
thingiverse
Customized version of http://www.thingiverse.com/thing:158717 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1101036 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1101036
thingiverse
Customized version of https://www.thingiverse.com/thing:964680 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=964680
grabcad
2-5/16" ball coupler measured with a standard tape measure.1/2" Pin pulled from McMaster
thingiverse
The original thing i remixed this from worked more like a stopper than a coupler. There was a wall in the middle preventing flow from one side to the other. ...I simply used Sketchup to remove the inner walls and exported it to this file here.