5 gallon gas can spout cap 3d models
1379545 3d models found related to 5 gallon gas can spout cap.thingiverse
We keep loosing the caps to our gas cans..... So, we duplicated them. These are the large 5 gallon cans. I design in Inventor, in inches, so you will need to scale up to 25.4. ...(I wish I knew how to do this for you up front....) I also included...
thingiverse
Three models are included, one closed lid, one lid with a 31 mm spout hole, and a spacer that is sized to fit a standard gas can spout gasket (1.45 mm od) and set into the gas can mouth. ... The v2 version has adjusted the threads to not cut as far...
thingiverse
Wanted a cap for the "Gas Can Spout" by rahaymore so I created it! ... Easy print that should work with your printers usual settings, could be a little shorter but it works.
thingiverse
Cap for norm8332's spout for 1 gallon metal can, with that you can store the spout into the can.
thingiverse
Since a can's threads may vary, and since a gasket or sealing washer may or may not be used, the cap orientation can vary, and the spout's direction can be adjusted accordingly. I printed this one in ABS, and the fit is good. The swivel is secure...
thingiverse
So I always use plastic bags after I've lost the gas cap. ...Then my father-in-law suggested one with a lanyard. An hour later this was born. once printed simply zip tie to the gas can and you will never loose your cap again :-).
thingiverse
Simple remix of user noslenwerdna's gas cap found here: https://www.thingiverse.com/thing:558998 I needed a closed cap for transporting fluids from my motorcycles for disposal in old cap-less gas cans, but didn't see anything made already. The...
thingiverse
I have two of these gas cans that came with my house. Somehow one of our caps got lost, so I scaled up the other one for this model. This cap is a direct replacement for the stock one and maintains all the same functionality. However this one is...
thingiverse
So, my funnel works well but it's impossible to tip the acetone from the can without spilling it everywhere so I guess a spout is in order. If you wait or come back, I'm planning on adding some kind of lid so this can be left in-place. Other...
thingiverse
This is a rubbery cap made to fit onto the gallon spout Instructions Make this out of NijaFlex 230 degrees C print speed 30 mm/s
3docean
Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi Format) - *.mb (Maya 8.5) - *.lwo (Lightwave 6) - *.c4d (Cinema 4D 11) renders Are made in 3ds Max 2008 using...
grabcad
Simply remove the plug from the bucket, and then push the spout into the hole until it snaps into place.Model #30669-00778https://doyleshamrock.com/product/5-gallon-pour-spout/I used the above website dimensions and provided image to make a rough...
thingiverse
This is a replacement gas cap for an older style (pre annoying locking spout version). Pint in Nylon for gasoline resistance. Easily removable support required (rotate 180 so it sits on the solid part when printing). ... Original on right new on...
thingiverse
... and buy one. ... Fits every one gallon paint can I have so far, so I suspect it will fit yours. I printed this with support which pops out really easy. Easy to press and tap on to the can, and easy to pry off. ... Enjoy and improve if you'ld like.
thingiverse
... made. ... I added a chamfer to the spout base so that you can print it without supports Instructions Print with the spout facing down, no supports. ... This will give you the smoothest surface where the can seals to the inside of the threaded area.
thingiverse
The cheapo nut that is used to hold the spout onto my gas can split near the top... here's my solution, I hope it helps someone other than me. ... Instructions I printed mine with a 25% honeycomb infill.
thingiverse
When the cap is screwed down around the nozzle the o-ring will get squished down to the top of the gas can and create the needed seal for gas not to leak out the cap. Use 3/4" CLEAR hose for the spout and cut to desired length(Clear is so you can see...
thingiverse
Tired of spilling Gasoline when you pour gas from a Gas can because its at the wrong angle.. I have invented an elbow that will point downwards that will attach to the end of the gas can and pour downward. Preventing future spills. I printed this...
thingiverse
This is a cap for a gas can spout. The inside diameter is 9.8mm and I updated the lanyard to 80mm. You can easily adjust the diameter of the cap by scaling the x-axis on your slicer or use the FreeCAD file. ... Let me know if you think of any good...
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515
cgtrader
Model formats: *.max (3ds Max 2008 scanline) *.max (3ds Max 2008 vray) *.fbx (Multi Format) *.obj (Multi Format) *.3ds (Multi Format) *.mb (Maya 8.5) *.lwo (Lightwave 6) *.c4d (Cinema 4D 11) renders Are made in 3ds Max 2008 using vray 1.5 (studio...
thingiverse
How I Designed This FreeCAD notes I'm not sure if there's a bug in freecad but for some weird reason you can't fuse the thread and the cap together to create a single part. ... In order to create the STL file, I had to select both the spiral and the...
cults3d
This is a replacement cap I made for the 7.6L and 11.3L watering cans from DCN Plastic (http://www.dcnplastic.com). In their catalog, the watering cans are the 7400 and 7500 models respectively. They are sold at Home Hardware in Canada and have a...
prusaprinters
I suggest consulting a chemical resistance chart to choose a filament type that matches well with your planned use. Note that I included a spout cap in the print - for use when keeping the spout on the can. Note that keeping the spout on the can will...
pinshape
With a 1 gallon can, I have trouble pouring Acetone into smaller bottles for ABS juice without spilling it. So I made this. It allows you to slowly pour directly into small containers without spilling. It doesn't have an air vent so you have to go...