5 inch hose 3d models
620952 3d models found related to 5 inch hose.thingiverse
Fits a 2.5 inch OD hose. Holds the hose in place but the hose can still be removed if needed. Requires 2 screws (the hole for the screw is around 0.15 inch in diameter). ... This was specifically designed for the Hakko FA430-16 fume extractor hose.
thingiverse
This is a coupler for ShopVac 2.5 inch hose. Made in OpenSCAD. Initial size was based on measurements of a commercially purchased coupler. Needed to tweak for printing, so went through some trial and error to get the best sizes/taper. I've printed...
thingiverse
A Quick Fusion 360 STL to adapt the Sweepy Dust Collector shoe to a 2.5" Shop Hose. The tolerances are a little lose to let you adapt as you see fit, I use a little rubber band around the 35.5mm tapered end to slip into the Sweepy, it has a little...
thingiverse
I obtained a De’Longhi portable air conditioner from work. ...Unfortunately the hose connector disappeared a long time ago. ...So I set about creating a new one.
thingiverse
This is used to vent a 3d printer enclosure with a 140mm fan and 2.5 inch hose.
thingiverse
Basic coupler for joining two lengths of 2.5 inch vacuum hose together. Made in Fusion 360. ... .STL & .STEP files included.
thingiverse
... a pool. Remix of 1.5 to 1.25 inch adapter https://www.thingiverse.com/thing:3714038 Threads scaled to proper size. Just print and install. ... Update: Uploaded new files with proper inside diameter of 41.5mm and changed seal thickness to 3mm.
thingiverse
... quite tall and it seemed like it was putting a lot of stress on the Plexiglas base. ... I designed this adapter to shorten the whole thing from three adapters down to one for use with a 1.5 inch OD vacuum hose. ... https://www.suckitdustboot.com/
thingiverse
I designed this dust collection adapter to fit over the HITACHI C10FCH2 dust outlet and to interface with a 2.5'' hose with hose clamp.
thingiverse
This is a hose adapter flange to fit snugly against a [Levoit Core 300](https://levoit.com/products/core300-true-hepa-air-purifier) air filter. I measured the diameter of the air filter at 212 mm, and the flange fits reasonably well against the...
thingiverse
Very basic adapter for a 140mm fan to adapter to an AC hose. ... I use this as part of my printing room venting solution. Along with an insert made for 5" AC code, the hose itself, and a 140mm fan and power to the fan.
thingiverse
Use 100% infill for airtight - don't cheap out on the filament. ... Tested PLA at 100% humidity for 24 hrs without a leak.
prusaprinters
Dust Collection 4-inch Port to 2.5-inch Hose Tapered Adapter Dust Collection Reducer FittingI suggest printing with these settings:Filament type: PLA (I used PLA+)Nozzle diameter: can be 0.4mm or 0.6mmLayer height: 0.3mmWall thickness: 0.6mmNumber of...
thingiverse
1/2 0.5 inch (approx 13 mm) hose barb to male garden hose adapter
thingiverse
https://www.thingiverse.com/apps/customizer/run?thing_id=1285949 Perfect fit to reduce 2.5 inch dust collection hose to Dewalt 779 dust exhaust port. The reducer also fits the 90 degree elbow (1.25" ID with extention) PVC adaptor I have attached to...
thingiverse
It's a flange for a 2 1/2 inch exhaust hose I'm using to vent fumes from my laser. Prints as positioned in STL with no supports. A 80mm fan fits in the back. ... The hose I bought:...
thingiverse
An adapter for a DeWalt DW421 orbital sander to a 1.5" [rubber hose boot](http://www.rockler.com/dust-right-universal-small-port-hose-kit).
thingiverse
This is an adapter that will route the output from a 60mm fan into an affordable 1.5'' flex hose.
thingiverse
Customized version of https://www.thingiverse.com/thing:1285949 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1285949
thingiverse
Customized version of http://www.thingiverse.com/thing:560647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=560647 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1285949 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1285949
thingiverse
This fitting was designed to be used in a Home Haunt Compression like Tunnel, but you can probably use it for other low pressure things as well. Below are the links to the Videos for the Home Haunt Compression like Tunnel in case you're...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9FhVap8YLfD
thingiverse
1 1/2 Inch Radiator Hose to Garden Hose Coolant Flush adapter. PLA is fine as it is running cool water. Works awesome. ...I also posted a 1 3/4 inch model.
thingiverse
This is a remix of my 2½" female to female blast gate (https://www.thingiverse.com/thing:4205443) except this blast gate attaches a 2" PVC Schedule 40 pipe fitting to a standard 2½" dust hose connector. The gate slides completely through the...
thingiverse
1 1/2 inch Coolant Hose Splice for fixing burst Radiator Hoses in an emergency only. DO NOT PRINT IN PLA!! IT WILL MELT. You engine runs temps of 190-220F if cooling properly. Use PETG 180F Glass Transition Temp EMERGENCY ONLY. ABS has a 220F...
thingiverse
This is to hold a 2.5 inch hose on the Onefinity so that it stays out of the way. I made this so you can just screw it into the top of the machine and use the existing screws. ...I included the Fusion 360 file in case you guys want to make any updates.
thingiverse
Needed a 5-1/2 inch connector for my portable air conditioner, saw andreq's, however was too small... so made one. Works great :) Print Settings Printer Brand: MakerBot ...