5 inch screen case for raspberry pi 3d models

Cover for Raspberry Pi 3D Scanner (PiClop) that runs FreeLSS scanning software (http://www.freelss.org/), a derivative of the Atlas 3D Scanner. You can order PCBs for the scanner from OSH Park - see https://oshpark.com/shared_projects/FvgkGJDE The...

This design is for the Prusa Bear full upgrade and was created to match either the original Einsy Rambo case or one of the SKR cases I designed: v1.3 - https://www.thingiverse.com/thing:3929513 v1.4 - https://www.thingiverse.com/thing:4723441 This...

This is a case for a Raspberry Pi Zero W with Camera. The camera module is a cheap chinese clone with the long flatcable.</p> <p>I tried to use as few metal screws as possible. Everything is printable except the USB connector and the screws for the...

I have a Raspberry Pi and the official 7" touchscreen that I've been using with Octoprint on my Ender 5. It's been sitting on my desk, its cables scattered all around, getting in the way and driving me crazy. To fix this problem, I built a sturdy...

I bought a 7" screen for my Raspberry (https://www.amazon.fr/gp/product/B071R2LMPH/ref=ppx\_yo\_dt\_b\_search\_asin\_title?ie=UTF8&amp;psc=1) and needed a case. Here it is. Print instructionsCategory: Electronics Print Settings Printer Brand:...

I tried to craft below, but I found it can't fit to my camera, so I made this instead. ... https://www.raspberrypi.com/news/raspberry-pi-can-revive-almost-any-super-8mm-camera/

Case takes a 40mm fan, however, there is very little vent holes in the case. ...i have remixed this with some vent holes in the rear of the main box and some vents on the side cover to allow the fan to draw/vent air.

Replace the lid of your Buddy Board with this drop-in case for your pi.Compatible with the standard and filament sensor cable covers.Although I have been running this for a while, without overheating, good heat syncs or a small fan is...

http://www.thingiverse.com/apps/customizer/run?thing_id=440268 Instructions Using the following options: build_plate_manual_x = 150 build_plate_manual_y = 150 header_type = 2.85 logo_horizontal_align = 0 footer_type = 2.85 footer_text = Raspberry Pi...

I added a part for a PIR sensor (HC-SR501) remixed from https://www.thingiverse.com/thing:2006787 I use this sensor : https://www.az-delivery.de/products/bewegungsmelde-modul?variant=8188899786848 I printed it face down with supports.

Expansions to the raspberry leaves logo provide ample room for showcasing the PiGlow, and careful widening of the GPIO opening on one side ensures seamless compatibility with the edge of the PiGlow board. ...Furthermore, removable feet have been...

After printing, it's necessary to cut a 3mm thread on both sides for the screws.

This creation was crafted using Tinkercad's intuitive platform. ...Make your desired changes directly within the website at https://www.tinkercad.com/edit?shareCode=4JHqydJ2c5c

This is a custom design specifically tailored for a Raspberry Pi that can be mounted on the front of a Lulzbot Taz (3, 4, 5, 6, and the upcoming 7) and provides an enclosure for the standard Pi Camera that focuses on the center of the printbed. I...

Mmdvm Duplex Hotspot https://a.co/d/5PH4abH To be able to connect usb cable, raspberry pi zero goes opposite side of the hotspot because of the modem size, so you need a jumper cable to make a connection between devices.

I couldn't find any cases that fit the touch screen I bought or the mounting method I wanted. So I designed this one, and I'm still messing around with additions to make it more functional.</p><p>The file includes both pieces that you will have to...

It's designed to hold a Raspberry Pi 4, and has accomodations for an LED power light and Power/Reset buttons (optional). There is room inside for either the Argon fan hat or the iUniker Pi 4 fan, but other fan/heatsink combos with a low profile may...

If you're looking for added security, I recommend using longer screws and nuts, such as 2mmx12mm with nuts for standard cases or backs with built-in connectors, or 2mmx16mm with nuts for add-on connectors. This project is ongoing, but the current...

... position of the lens arm. The high position of the Raspberry also gets better Wi-Fi signal and better cooling than my old closed case under the frame/electrics. ... Thanks to agarajag, hackoholic, and all the others for creating such cool models!

I haven't tested any other models. Additional Parts:     2 M3 screws (not too long otherwise they may collide with the extuder) Assembly:Attach the bottom of the case with the screws as shown in the picturePlace the Raspberry in the caseClose it with...

Hi, I made this simple minimalistic pi case that can be printed in 2 tone or single colour… (Pokeball colourway would be cool) The 2 parts snap in place on the side.Hope you like it.

added holes at bottom to mount and two holes for pi camera ribbon cable on the top

Featuring a 4.2-inch eInk screen, its concept revolves around displaying information in a rotating manner, updating every couple of minutes. The data can be any feed - from the latest news headlines to your smart home energy usage, live local...

This is a modification of the case that is featured here: https://www.thingiverse.com/thing:2832531 I have added a slot for the header pins, a hole to view the power status of the LifePO4wered board from above, removed the fan attachment points and...

The Raspberry Pi 4 (3 should also fit) mounts to the official 7 inch touchscreen display. The display mounts to the mount. ... Test prints were done in PLA, but I would use PETG or ABS for a final print, as it will be more suited to the high...

Designed specifically for the Raspberry Pi 3, this wall mount is ready for your next project. If you have any ideas or recommendations for version 2, feel free to share them in a comment below. Have fun printing it out! UPDATE 30.10.2016: It turns...

I believe the vertical orientation of the Raspberry Pi makes it easier for air to circulate over the CPU.This print is comprised of these parts :Enclosure - the main piece (this includes an invisible “window” in front to show LED activity; the LEDS...

Print it so the prusa is upside down with support on build plate, I used PETG with 20% infill.The pi and case i used is from amazon https://www.amazon.com/gp/product/B07XTRK8D4/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&amp;psc=1 I love that it gives...

I wanted a robust stand for this case that I really liked: https://www.thingiverse.com/thing:1164446 The left and right pieces are mirrored duplicates of each other, connecting to the LCD screen through two case parts using M3x10 screws. I also added...

Wanted a stand to have the pi vertical for better cooling and smaller footprint on my desk v1.2 is the one I printed in the photo v1.3 has a cutout for the pi to be stood with the usb ports facing upwards without smooshing the sd card