5 inch screen for raspberry pi 3d models

10°) to stop the Pi and Case clashing with the PSU on my Kossel Linear Plus. I also added some chamfers and rounded corners just to please my OCD ;-)I mounted the bracket to the extrusion using 5x12mm screws and t-nuts. The LCD was mounted to the...

This is just a simple stand that holds the Touchscreen as well as the IO-Board. ... I use this for developing for the cm4.

[Mark II (link)](https://www.thingiverse.com/thing:4625811) and [Mark I (link)](https://www.thingiverse.com/thing:4300960) With Mark III, I completely rethought the design, which allowed to: * increase the number of raspberries in 2 rack units *...

The MHS or LCD touchscreen from Jun-Electronics fits seamlessly into this case, and I'm confident that similar screens will also work just as well on the Raspberry Pi's GPIO pins. I also took the opportunity to add some ventilation holes to the side...

I was not satisfied with the previous holders, which broke during transport. So, with several failed attempts, I designed this model. The transition at the top can be printed at a suitable speed without support. If you have a lot of PLA to spare and...

Mount for a 5" raspberry pi screen for an ender 6. This doesn't replace the stock screen, but instead sits to the left of it so you can retain the original screen. you will need to cut or remove the left perspex door to fit this, and you'll need to...

3.5 inch TFT LCD touch screen waveshare. ...Arduino Shield.assembled in a bracket with M2x8 screws and M2-IUTB-inserts.Designed By Alon Rahamim from Trixel Engineering.

I remixed the original case from https://www.thingiverse.com/thing:4354970 and added the camera clip from https://www.thingiverse.com/thing:4578487 -Added clips to attach it to the ender 5 top bar -Added a pi cam adapter located just above the heat...

I couldn't find a case/stand to fit this 5" Pi/touchscreen combo that I am using for Fluiddpi and Klipper on my Ender3v2, so I made one. An optional extra is this 12-24v usb power device that is wired to the Power Supply to power the Pi and the...

This enclosure is tailored to house a Raspberry PI 1, 2, or 3 model, along with two hard drives: one 2.5-inch and one 3.5-inch drive. ...The design of this case has evolved from my previous Storj.io Raspberry PI NAS enclosure, but it's not compatible...

Screen case for Sunfounder Raspberry Pi 4 Display Touchscreen 7 Inch Case (HDMI & USB)

For this make, I choose to setup only 3 raspberry pi, and I remake the cover to fit with exactly 2 x 80 mm fans. I also create a right flat cover for the air fow and thiner separator. ... 3 parts not included here: - The right ear, see the remix from...

Raspberry Pi DIY enthusiasts are now empowered to create their own custom wall-mounted display using a simple, innovative design tailored specifically for the 5-inch Raspberry Pi LCD screen. ...The project is showcased in an easily accessible YouTube...

It is a simple and very basic desig that makes easy to print a tft display for the 5.6 tft available on several chinese webs and ebay. It takes advantage of the already existant screws. it is a tight fit and it will hold it by itself, you only need...

This is a remix of the screen cover to include a raspberry pi 3b (for Octoprint) mount behind it. Its a perfect fit and allows the screen parts to be used, blocking out any unwanted light from the display. Printed in black it really helps to...

In addition to the printed parts you will need the following parts: Elecrow 5 inch LCD Display-B https://www.amazon.com/dp/B07FDYXPT7 4 x M3 4mm 5mm Threaded Inserts 4 x M3 8mm 5mm Threaded Inserts 4 x M3 4mm Screw 4 x M3 8mm Screw Also here are the...

Case for the **Raspberry Pi 4** with **Waveshare 5.5" AMOLED** screen and **Auvidea B102** HDMI to CSI interface. Three parts - lid, pi case and screen case. The former two should be tied to the screen using screws. **Work in progress** - the lid...

Raspberry Pi to Monitor Adapter - Raspberry Pi Screen Adapter Converts your Raspberry Pi into a full-fledged computer with a standard screen connection.

For official Raspberry screen

Case Design for Raspberry Pi B3 Featuring a 5-Inch Display and Dual 18650 Battery Power

A single 3.5-inch LCD display designed specifically for the Raspberry Pi by Waveshare.

Raspberry Pi case for Babylon 5 fans.

Transparent case for Raspberry Pi

I have just completed designing a casing for the Raspberry Pi 3(2) with a 3.5-inch touchscreen display. This design was primarily intended for use as an OctoTouch or AstroTouch case, but it can be used for any purpose. Note: Both parts are printed...

5 parts. ... Easy to print. 4 x M4 (50mm) screws. 4 x M4 nuts. Glue required. Designed for: Raspberry Pi 4 Model B Raspberry Pi 3 Model B+ Raspberry Pi 3 Model B Raspberry Pi 2 Model B Raspberry Pi 1 Model B+

Remix of the screen bezel in order to accomodate a bigger ans faster waveshare 4" TFT screen: https://www.waveshare.com/wiki/4inch_RPi_LCD_(C)

Simple 2 parts assembly case for the Raspberry pi 3 with the 7" touch screen. ...It uses the screw threads on the raspberry pi, making the design simple and versatile.

Mount for Official Raspberry Pi Touch Screen LCD

This is an innovative design, thanks to drifkind's original work that has been skillfully remixed https://www.thingiverse.com/thing:4020018/remixes Bill of Materials: 1) A Raspberry Pi 4 Model B Computer:...

I'm revisiting my initial plan to craft a custom enclosure for a Raspberry Pi 3B, this time around getting it right - the holes for the 4-inch HDMI screen from Waveshare and the Rii Mini Bluetooth Keyboard will be perfectly aligned.