▷ 5 mm hook 3d models 【 STLFinder 】

5 mm Hook
thingiverse

Customized version of https://www.thingiverse.com/thing:53854 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=53854

5 mm Crochet Hook
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: throat_angle = 10 length_above_grip = 60 diameter = 5 length = 150 narrowing_slope = 20 narrowing_length = 10 narrowing_ratio = 0.16...

Parametric crochet hook 5 mm
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: hook_length = 5 narrowing_slope = 20 length_above_grip = 60 diameter = 5 narrowing_length = 10 throat_angle = 10 length = 155 grip_slope = 5...

Bathroom radiator spring hook - 20.5 mm
thingiverse

Remix of layershifter's Radiator hook. ...I changed the inner diameter to 20.5 mm.

Hook for 5 mm shelf adjustment holes
thingiverse

This is a small hook that can be easily mounted in a kitchen cabinet with standard 5 mm shelf adjustment holes.

Bathroom Radiator Towel Hook 20,5 mm
thingiverse

Remixed for use with other radiator (20,5 mm) PLA is not good idea when the radiator is full-time hot ;)

Headphone Hook For 5 mm Holes (IKEA)
thingiverse

Hook to store your headphone at your IKEA table.

Snap in wire shelving hook - 23.5 mm
thingiverse

Shortened the attachment side to fit my wire shelving with a ~23.5 mm height. ...The internal dimension is meant to measure 23.5 mm, though my print came out around 22.9 mm. ...Fits fine though.

Bathroom radiator hook for 22.5 mm diam
prusaprinters

Bathroom radiator hook for towels and the radiator has 22.5 mm diam horizontal elements. 

Hook Cupboard 19,5 mm Door
thingiverse

Customized version of https://www.thingiverse.com/thing:4735485 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4735485

30mm hook with screw keyholes 5 mm
thingiverse

Customized version of https://www.thingiverse.com/thing:2779381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2779381

hook with ball 10x100x62.5 mm
thingiverse

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/09YlPiDbRtI

Thin, single-thickness mask strap / band with additional smaller hooks (0.5 mm thick)
thingiverse

We have found this 0.5 mm thickness to be preferred over thicker and thinner designs, but the thickness can be adjusted as desired by scaling the model in the z direction. The included 2D .dxf file has all curved features defined by continuous arcs...

MPCNC-C (23.5 mm conduit) Spool Hook with Filament Guide
thingiverse

I was tired of my spool constantly unraveling, and hanging it on some of the extra conduit seemed too simple of a solution to stick with permanently, and thus I designed this! It's based on the shape of the 'Flashforge finder spool holder with...

Shower hook for glass cubicles 5/6/7/8 mm
thingiverse

... If you need to adjust for your case - you can use the source file published at https://www.prusaprinters.org/prints/120359-shower-hook-for-glass-cubicles-5678-mm-parametric and change params I've printed it with PLA, 0.2mm layer and 20% infill.

JaqLoopie - Phone Strap Charm Loop/Hook for 3.5 mm Audio Jack
thingiverse

... that I cannot strap a [3D Hubs Marvin](https://www.thingiverse.com/thing:215703) to it. JaqLoopie is meant to solve this obvious design flaw. Plugged into any 3.5 mm stereo jack JaqLoopie it will hold on to your (light weight) phone strap charms.

Simple Wall Hook / Hanger with 4.5 mm tapered screw hole
thingiverse

This is an enlarged version of mtuieee's simple hook, redesigned to fit a countersunk 4.5 mm screw in the middle. You can scale it to be larger/smaller and therefore fit smaller/larger screws as well. The hook's base is 38×38 mm and the hook is...

Shower hook for glass cubicles 5/6/7/8 mm (parametric)
prusaprinters

I have designed a parametric hook - as an exercise to learn parametric design in Fusion 360. I was inspired by another design which I've found online, but I needed to adjust it for 6mm glass.</p><p>This print should fit glass shower cubicles with...

Headphone hook for Ikea "LINNMON" desks (34,5 mm)
thingiverse

Simple remix to adapt the headphone holder to my Linnmon desk

Shower hook for glass cubicles 5/6/7/8/10 mm (parametric)
prusaprinters

I have designed a parametric hook - as an exercise to learn parametric design in Fusion 360. I was inspired by another design which I've found online, but I needed to adjust it for 6mm glass.</p><p>This print should fit glass shower cubicles with...