5.25 drive bay converter 3d models
735029 3d models found related to 5.25 drive bay converter.thingiverse
Installation instruction Once you have purchased your flush mount kit and printed the 2 £D Printed parts you will need to do the following Install the flush mount extention into the 5.25" front panel you have printed Remove the PCI slot plate...
thingiverse
Was repairing an older PC and didn't have the specific drive bay cover. I was hoping to find a generic one on thingiverse but everything was either made to clip into a specific case or was an adapter for something else. Made this real quick and it...
thingiverse
Was repairing an older PC and didn't have the specific drive bay cover. I was hoping to find a generic one on thingiverse but everything was either made to clip into a specific case or was an adapter for something else. Made this real quick and...
thingiverse
I was repairing a PC, there was not enough cover 5.25". I made a model for a specific mount. Mounting does not require screws. ...The photo shows the latches on which the cover is attached, and you can also see how it is fixed.
thingiverse
Handy storage drawer for 5.25 inch optical drive bay, fully customisable
thingiverse
This is 5.25" CF-card adapter drive bay for older computers to replace hard drives with CF-cards that can be easily accessed from computer front panel. Two CF-card adapters can be installed in this 5.25" drive bay. ... Compatible CF-Card adapters can be...
thingiverse
5.25" drive bay cover for Bitfenix Prodigy ITX case. ... Usable with fan screw holes on print.
thingiverse
A cup holder attached to a 5.25" drive bay cover. ...Free up your CD-ROM tray once again!
thingiverse
5.25" Drive bay for hackintosh computer. ... All units are in imperial so if your system is metric scale to 25.4"/mm or 2540%
thingiverse
5.25 drive bay cover switch Panel I remixed for my Fractal Design Define R4.. ... Recommend 12-15% Infill and 3 Perimeters
prusaprinters
5.25" Drive bay for hackintosh computer. All units are in imperial so if your system is metric scale to 25.4"/mm or 2540% Category: Electronics
thingiverse
Cover for a 5.25" optical drive bay. Uses the screw holes from an actual drive. It can be used with ANY computer case. Most computer case makers include proprietary covers. ... Drill the holes to about 2.8mm and make thread screwing in a standard...
cults3d
Cover for a 5.25" optical drive bay. Uses the screw holes from an actual drive. It can be used with ANY computer case. Most computer case makers include proprietary covers. ... Drill the holes to about 2.8mm and make thread screwing in a standard...
prusaprinters
Cover for a 5.25" optical drive bay. Uses the screw holes from an actual drive. It can be used with ANY computer case. ...Most computer case makers include proprietary covers. Drill the holes to about 2.8mm and make thread screwing in a standard optical...
prusaprinters
A vertically oriented dual 5.25 inch drive for the Corsair P3 computer case.Print SettingsPrint with the bottom side on the build plate (for orientation see P3 Dual Drive Bay.3mf).Needs lots of supports
thingiverse
This is a faceplate to fit an Amstrad 3" disk drive into a 5.25" drive bay. It is a nice snug fit and the deep nature keeps the drive very securely in place and prevents it going any further back on the EME-156 model of 3" drive I use. Note that...
thingiverse
Covers the 5.25" DVD Drive Bay snugly and clips in place. Instructions It is a tight fit and will flex just enough at 50% infill to pop in. I put the top in first and then the bottom (or left then...
thingiverse
5.25" Drive Bay Case for the MMS, Mister MultiSystem. These are also Stackable. There are two versions, one is the same size as the MMS, the other is longer to accommodate longer 5.25" devices. Both will fit on the Ender 3 bed, The longer...
prusaprinters
5.25 inch bay cover for a Corsair Carbide Series 300R tower. ...Might work in other cases.</p><p>The source files are hosted on Onshape:<br><a...
thingiverse
this is a 3 part design, very simplistic in nature but effective in execution (if I do say so myself) it uses the two 5.25 bays typically only available in a mid-atx case and positions the 120mm fan at a angle suitable to fit but still flow air...
thingiverse
A vertically oriented dual 5.25 inch drive for the Corsair P3 computer case. Print Settings Print with the back side on the build plate. ... Needs lots of supports
thingiverse
... kept in a convenient place - right on front of your PC! ...It holds 10 SD cards and uses one 5.25 bay to mount in. I haven't had a chance to print this model completely yet, so I'll mark it as a work in progress. ... Comments and suggestions welcome!
prusaprinters
Help Your PC breath! 5,25" bay plate to improve airflow drastically. Custom supports already in place, just print it and snap off after! ...No additional work needed. </p><p>Better to use PETG because it needs to be flexible. <br>PLA...
thingiverse
A while back someone made a drive bay adapter for the HTC Vive linkbox and I wanted to make something similar for a friend that owns a Valve Index (and for me when I eventually buy my own). I've only tested this print with my own machine, and the...
prusaprinters
<p>I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.
thingiverse
This lets you easily secure another 3.25" floppy drive In the Amiga 2000's 5.25" drive bay. It probably works in other 5.25" drive bays but it hasn't been tested. I made this specifically to mount a Mac floppy drive in my Amiga 2000 for use with...
thingiverse
Three part print for adapting a 3.5" drive into a 5.25" drive bay. Make sure to align the front surface of the front plate down. Use four M3x6mm screws to attach the front plate to the side braces. ... Designed to mount the 3.5" drive from...
thingiverse
3.5" to 5.25" drive bay adapter for mounting your 3.5" HDD in CD-ROM compartments. Adapter designed according to SNIA specifications and could accommodate two standard 0.7"-high drives or one 1.028" and additional 0.7" drives in standard 43mm-high...
youmagine
Small bracket for mounting a 2.5 inch SSD in a 5.25 drive bay. Small enough to be printed on an Ultimaker 2 GO but still sturdy. ... Not very space-efficient, so mostly for use in larger cases with room to spare.
thingiverse
These screw in like a 5.25 inch or 3.5 inch drive. I also included the dual fan cover that I created this for initially and a 120mm fan cover for completeness. There is also a cover with slots for 4 usb and 2 headphone jacks that was recycled from...