5.25 hdd bay 3d models
643749 3d models found related to 5.25 hdd bay.thingiverse
This is a redesign, i tried to make it work without glue, but not sure if it works for every plug or what is the better way in the end. ... though i think the 3,5" frame looks quite good and places the HDD inside your computer. ...
thingiverse
Adapter that alow place 2 hdd SSD and standard 3.5 inch drive into 1 5.25 bay
thingiverse
Use these to mount a 3.5" hdd into a 5.25" cd bay in a computer tower. ... It offsets the drive away from the front of the computer 5mm rather than centering it in the bay.
thingiverse
* Front bay long - a longer bay, else similar to front bay short * Disk Bay 3.5 - a bay to hold a 3.5" HDD, with or without one to three 40mm fans at the front side * Disk Bay 2.5 - a bay to mount up to six 2.5" SSDs and optionally one to three...
thingiverse
... Depending on your case you can maybe not use all the 5.25 bay screws but it should be enough to fassten one adapter because the 5 drives hold everything together. ... Drill the outer screw holes with a 3mm drill if they are to small after print.
thingiverse
pointy end tward the front of the drive uses 3mm screws for odd and standard screws for hdd
prusaprinters
It has fit all standard optical bays we have tested it in and allows you to fit an extra 2.5" from the bottom or 3.5" drive from the sides.If you find any problems with the model, please let us know and we will attempt to fix them within...
thingiverse
Dirty remix of usermod's hdd adapter. This one uses less filament. I believe it is still structurally sound, as the tension is on the mounting points and the drive and case, instead of the center beam. Should print faster too. Thanks usermod for...
thingiverse
The holes that line up with the hard drive are 4.0 inches apart, the holes that are used to mount to the drive bay are 3.1 inches apart. The hole diameters should be close enough to use the fasteners you may already have. ...Print Settings Printer...
thingiverse
... may end up working in other 2.5" caddy-insert type adapters. IDEALLY, together, we can source some sort of backplane, and just design the entire 5.25" insert from scratch and just order cheap backplanes to accommodate it. ...That would be awesome.
prusaprinters
The spring will work hard to keep it locked. A Thermaltake Max 1562 is what this is designed for, however, since they're rare, its very likely that this design may end up working in other 2.5" caddy-insert type adapters. IDEALLY, together, we can...
thingiverse
Couldn't find an adapter that fit right for me, so I whipped up this 5.25" drive bay to 2.5" SSD / HDD adapter. Two drives fit stacked, and standard mounting screws should fit fine. I used M3 button head screws for the SSD / HDDs with normal coarse...
thingiverse
Since most SFF PCs only have one 5.25" drive bay, I thought that it would be useful to create an 5.25" case which has two slots which can be used for either a slim laptop DVD drive and a 2.5" HDD drawer, or two 2.5" HDD drawers, to allow direct...
pinshape
... PLA for caddy. PLA or ABS for front panels. Allowance for front panels is calculated for 0.4 mm nozzle. Front panels are loose, if You use 0,3 mm nozzle(have to glue them to the caddy base) and probably hard to slide, if printed with 0,5 mm.
thingiverse
... Notes: Allowances for front panels(sliding them in place) are OK with 0,4 mm nozzle. It`s loose for 0,3 mm nozzle and probably hard to fit, if using 0,5 mm one.
thingiverse
this is an adapter for that old case with tons of cd 5.25" bay, you can get a very cool hdd with the optional 120mm fan mount
cults3d
This tray holds 8 2.5" form factor drives, up to 10mm thick, has screw mounting holes for the 5.25" bay with slots to allow clearance on the ODD rails in most cases. also has screw holes to mount the drives in it, but they should stay in by...
thingiverse
This tray holds 8 2.5" form factor drives, up to 10mm thick, has screw mounting holes for the 5.25" bay with slots to allow clearance on the ODD rails in most cases. also has screw holes to mount the drives in it, but they should stay in by...
thingiverse
I removed its drive bay, because it was at the bottom, where giant GPU+cooling (see my TESLA M40 92mm fan adapter) would go. So I needed to find place where the RAID array would go. The design by Schoba was what I needed - simple and easy to...
thingiverse
This is actually a full remake of the model from scratch using Fusion 360. I printed the original item and it's great, but I wanted the drives to stay a little further in the back, so I decided to make my own version. Since this saved a lot of...
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
this is an improved version of the 120mm fan mount, this can easily be instaled with a few screws
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845
thingiverse
Customized version of https://www.thingiverse.com/thing:4117845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4117845