50mm cooling fan 3d models
177597 3d models found related to 50mm cooling fan.myminifactory
Thin bracket for a 50mm fan, positioned to cool electronics board.
thingiverse
I designed a cooling fan mod for my Malyan M180, to mount a 50mm blower fan on the side of the extruders. This bracket can be placed on the left or right side, and is held under the extruders by 4 small pins. There is no physical modification...
thingiverse
Redesign of the 40mm version by CreoTek, designed for a 50mm fan.
thingiverse
The xl6009e1 step-up converter and 50mm fan motors are located on the top of the case.
cults3d
The xl6009e1 step-up converter and 50mm fan motors are located on the top of the case.
thingiverse
Customized version of http://www.thingiverse.com/thing:166045 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=166045
thingiverse
I remixed this design to cover the larger 50mm fan cover for my Anet A8. ...After printing in green PLA, I colored it in with black and white sharpies to bring it to life.
thingiverse
If you want to mount beefy part cooling fans without colliding with a smaller CoreXY frame, this might work for you, too. Compatible with probe mounts from my [Compact Hemera mounts for 40mm blower fan, inductive sensor, and HyperCube...
prusaprinters
To make the most of the space available on my HyperCube, I designed this mount to only take up space in the positive Y axis relative to the Hemera. If you want to mount beefy part cooling fans without colliding with a smaller CoreXY frame, this might...
thingiverse
50mm Layer cooling fan shroud. Snaps onto the stepper motor that runs the extruder gears in the hotend. Used simple ABS slurry to glue the 3 parts together. Printed them as separate files so I could avoid using supports. This is still a work in...
thingiverse
Upgraded fan duct to use a 50mm fan for part cooling on an Ender 3/CR10. The duct is single sided, leaving space for a bed leveling sensor. ... Hardware: Fan: https://smile.amazon.com/gp/product/B00N1Y47PQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1...
pinshape
Summary Cooling fan mount for 50mm Radial fan (eg http://www.banggood.com/3D-Printer-12V-DC-50mm-Blow-Radial-Cooling-Fan-p-980653.html). Fan slots in to mount and pressure fits - no glue etc necessary. Works a treat - be warned you can end up with...
thingiverse
Cooling fan mount for 50mm Radial fan (eg http://www.banggood.com/3D-Printer-12V-DC-50mm-Blow-Radial-Cooling-Fan-p-980653.html). Fan slots in to mount and pressure fits - no glue etc necessary. Works a treat - be warned you can end up with too much...
thingiverse
It's about as compact as you can get, fits around the stock hot end cooling fan, and it mounts on the front of the carriage, so it doesn't interfere with the side of the printer or bed clips as much as the wider ones. So far, I've printed my first...
pinshape
It's about as compact as you can get, fits around the stock hot end cooling fan, and it mounts on the front of the carriage, so it doesn't interfere with the side of the printer or bed clips as much as the wider ones. So far, I've printed my first...
thingiverse
A 50mm axial blower/fan is probably the best alternative you can get for your 3D Printer and i can only recommend the upgrade if you are still running on the standard issue 30mm fan (or even on a 40mm fan). There are some fancy all surround part...
thingiverse
Simple no-frills frame for mounting 2 x 50mm fans that you screw down onto ply-board mounting next to your MKS board. Works with basically any MKS board as it's not attached directly. It was specifically designed to work optimised for MKS Base 1.4...
thingiverse
The Paps 414F fans (40mm) are rated 4.7CFM @ 24v @ 22.1 dBA @ 5400rpm Long of it short, a 50mm fan underdriven will be quieter yet flow more air (assuming we get a linear drop in output). ...Thruit00 uses Paps 414F fans, but these are 40mm fans which...
thingiverse
Adapter designed to fit 50mm cooling fan in 40mm filament cooler socket. ... Eg: http://www.thingiverse.com/thing:420204
thingiverse
... and One for Cooling Model. 11/3/2014, Add two file 1.extend the cooling model side exit (for 40mm fan) 2.extend the cooling model side exit (for 50mm fan) Instructions PLA with 0.2mm layer no using support Dig screw hole by hand after printing
thingiverse
I add a adapter 60 to 50 fan. ...Now, you can use your 50mm fan instead.
thingiverse
This is a model of a radial cooling fan, 50mm x 15mm, of the type often used in 3D printers. This is probably not something you would want to print (unless you are building a mockup). It is a component that you can use to design other stuff. ... ...
myminifactory
This is a fan duct for the radial cooling fan, it prevents air disturbance on the print. Only a little bit of support is needed, can be very easily removed. ... I made this model for the PimpMyPrusa contest in Solidworks, I don't have a Prusa printer...
thingiverse
It is a bed cooling shroud for the 50mm fan that comes with the 24v upgrade. Instructions Print his filament drive and extruder cooling shroud, and print my mount and shroud. A little touch up on the dovetails, pus a little paste wax makes for a...
thingiverse
Cooling Fan for GeeeTech i3 ProB, take a look at: [Prusa i3 basierte Drucker: Verbesserungen und Anpassungen](https://www.libe.net/printer-mods).
thingiverse
This idea is a remix of the http://www.thingiverse.com/thing:63123 50mm Supportless, Directed Cooling Fan Duct for MendelMax & Prusa
thingiverse
Found the hole spacing didn't work for me (duh, what I had was a 60mm fan). The hole centres are 50mm. Designed this for top mount. Your fan may fit underneath, who knows? Make sure you've got clearance for that rat's nest of wires. ... Edit: ...
prusaprinters
Found the hole spacing didn't work for me (duh, what I had was a 60mm fan). The hole centres are 50mm. Designed this for top mount. Your fan may fit underneath, who knows? ...Make sure you've got clearance for that rat's nest of wires.</p> <p>Edit: V2...
thingiverse
Radial Cooling 5015 Fan (50mm) DC12V STEP file for your CAD projects