510 thread 3d models
88502 3d models found related to 510 thread.thingiverse
This is a container for common 510 thread draw batteries and the things you might choose to use with them. ... It has a pot leaf on the case, original leaf available through the remix link.
thingiverse
Here I have designed 3 Vape tank holders for 510 Threads and 22mm tanks. You can either have 7x 13x or 19x slots. ... Many thanks
grabcad
This heatsink model i made by measuring the sample i have.This is SS heatsink with both sides 510 thread and insulated central positive pin.It's purpose is to avoid heating of boxmod (or battery) from atomizer's heat.It is supposed you're screwing it...
thingiverse
Small desk caddy to hold 510 thread vape pen batteries and cartridges. Can hold 3x batteries and 6x cartridges of common size. The cartridge holes are shaped to accept the threaded piece which "locks" it in place. Additional pieces used (purchased...
cults3d
This is an atomizer stand with 510 thread, the standard for atomizers and clearomizers on the market. There are 2 versions, small and big, which differs by the height. The small one is 2 cm tall (0.78″) and the large one is 3 cm tall (1.18″). I...
myminifactory
This is an atomizer stand with 510 thread, the standard for atomizers and clearomizers on the market. There are 2 versions, small and big, which differs by the height. The small one is 2 cm tall (0.78″) and the large one is 3 cm tall (1.18″). I...
thingiverse
This is an atomizer stand with 510 thread, the standard for atomizers and clearomizers on the market. There are 2 versions, small and big, which differs by the height. The small one is 2 cm tall (0.78″) and the large one is 3 cm tall (1.18″). I...
thingiverse
A caddy for 510 thread cartridges that are 12mm diameter or smaller. Holds 16 in a 4x4 grid. ...
thingiverse
You will need adapter for Vinci original / X / R to salvage 4 magnets that goes into 4 small holes on the edge and the actual 510 thread, that is pressed together with two pieces. You just destroy the original plastic, salvage magnets and two pieces...
thingiverse
This is a holder for 510 threaded vape cartridges. It holds 8 cartridges 12mm in diameter or smaller. ...There is an octagonal cavity for storing small items like rubber caps, magnetic rings etc.
thingiverse
Pretty basic. Made in Fusion360. Holder designed to keep your cartridge from clogging or leaking. [Leaf stamp was remixed from kyleaj1s's leaf stamp](https://www.thingiverse.com/thing:3534472) This one was designed for the b-smart battery by...
thingiverse
Vaporizer lanyard & caps. ...(14.6mm outer-diameter) For 510 and Ego style threaded vaporizers. The caps fit the batteries and both ends of the tanks. ...Vaporizer pictured is the VaporFi PRO II.
thingiverse
Center cut is 6.8mm to fit the 510 threaded atomizer. Center cut on the full 510 file, is 9.2mm, to fit the entire 510 socket connector through the spacer. ... Instructions Used FreeCAD, made some very...
thingiverse
This is my first upload here. ...The slot where the 510 thread seems to sit fine, but the varying base size of the different 510 cartridges may not fit.
thingiverse
A place to store 510 threaded cartridges that need to stand upright. Allows the last little bit to settle to the bottom to be able to finish the cartridge before throwing it away. ...Holds 24.
thingiverse
... there. ... This holds the narrower 10mm cartridges (510 thread), with 12mm openings for some extra room. There are S and I markings labeling the columns. ... If you also use Pax Era pods, you might like: https://www.thingiverse.com/thing:3155296
thingiverse
Hiya, Here we have a tank stand more than capable of holding all your collection of 22mm 510 threaded vape tanks. ... Enjoy and many thanks
thingiverse
Support for atomizers with 510 thread for vapers, it has a thread inside so that the atomizer does not fall when moving it from place, the thread is M7x0.5...
thingiverse
Don't EVER use the phrase "510 thread" again. I am triggered. ... This model was made in anger.
thingiverse
If you are having trouble getting the 510 threads to print clean then you can run a M7-0.5 tap through the threads to clean them up or use one of the 510 adapters as a heat set insert small jars-...
thingiverse
- 6 slots for 510 thread cartridges - Large hole for the Yocan Evolve Maxxx - 2 slots for concentrate spoons - Open face, 36mm wide, angled backward slot for a concentrate box - Forward angled slot for an Exxus Snap Mini Printing Notes: I'm using...
cults3d
A sized 510 thread battery/ cartridge holder for the legal cannabis extract cartages available in the land of the true north strong and free. ...Holds up to 15 battery's, 510 cartridge and or joints.
thingiverse
A sized 510 thread battery/ cartridge holder for the legal cannabis extract cartages available in the land of the true north strong and free. Holds up to 15 battery's, 510 cartridge and or joints. ...
thingiverse
This is a carton designed to hold 4 standard 510 thread vape carts, height can be adjusted, but I just set it for the carts I happen to get. It uses a size-on-size interference fit on the carton that is not ideal, and works better after some light...
thingiverse
... the .IPT(Autodesk Inventor 2020) and the .STEP files for anyone that wants to edit this. The two cartridge holders on the sides should fit standard 510 thread cartridges. ...The base was designed so that this whole assembly won't tilt over easily.
thingiverse
510 connector for mod vape 510 literally means 10 threads at 0.5 mm per thread. The diameter is 7mm. ...If you were to create this thread yourself, it would use an M7 x 0.5 tap.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1685090 Instructions Using the following options: xOffsetSquonkCutout = 10 xOffset_510 = 0 xOffsetPcb = -21.4 zOffsetFireSwitch = 90 xRotateFireSwitch = 0 xRotateSled = 90 boxType = hammond1590g...