533 tiny trainer 3d models
26561 3d models found related to 533 tiny trainer.thingiverse
This is a replica of the tiny trainer DRL Racer 4 like camera mount, but for the runcam hdzero, and fixed at 45 degrees. Print it upright, 20% infill in TPU. I run the TPU a little hot (230) to provide extra rigidity since I kept it as light as...
thingiverse
Strengthened DJI cam mount for the 533 tiny trainer remixed from the originals and strengthened a little. ...Has holes to mount the adapted BetaFPV Hero lite backplate (use carbon front plate as per original)
thingiverse
4" and 3" pods for the 533 Tiny Trainer. The thick arm version is if you have really thick leds on the arms. ...I don't recommend it because it only has a few millimeters of clearance with the prop.
thingiverse
This is a remix of the original battery holder for 533 Tiny Trainer. I modified it to use less material to be lighter and be able to fit bigger variety of batteries like the RCBattery.com Liperior Pro 3S 550 HV for me, while keeping original battery...
thingiverse
FT Tiny Trainer Power Pod Firewall for D1806 motor. ...Flip model before printing.
thingiverse
Simple wall mount for Tiny trainer R/C plane. ...Designed for drywall screws.
thingiverse
Stylefin for the Tiny Trainer. ...looks good and works fine for turtling and protecting the cam lense
thingiverse
Rate tool for the FliteTest Tiny Trainer. The only measurement i could find for angle on the plans was 16*. ... If i had to guess low rates are between 3 and 7 degrees less.
thingiverse
I designed this landing gear for my tiny trainer by Flite Test. The slot for the fuselage is 51mm across. ...If you would like to see photos and video of it checkout my Instagram @gigrprintr.
thingiverse
I designed this launchpad for my Tiny Trainer. The guys over at Fly533 have a "official" one. But it is so big and bulky. This will take approximately 1/3rd of the plastic and time to print. My goals with this were: * LESS PLASTIC *...
thingiverse
This is a fuselage, firewall replacement for the Flitetest Tiny Trainer. The nose of the plane is two inches shorter but plenty of room for batteries. I have flown this and had very good success. Parts should be CA glued together. The hatch has a...
thingiverse
I wanted to fit a Caddx Vista in my Tiny Trainer and didn't want to buy the conversion kit from five33 (Not that its expensive, but shipping was 4x more than the part). So I designed this up. Works perfectly fine for me! The top plate I printed in...
thingiverse
This is a arm protector for my tiny trainer so i won't have to worry crashing on concrete. ... Enjoy printing
thingiverse
FT Tiny Trainer power pod with 2° right angle and 2° down angle. Motor holes are 16mm apart. Perfect for a 2205 motor. ...
thingiverse
Two is always better then one, so mount two motors on your tiny trainer sportwing, and use the glider nose. ... Print Settings Printer Brand: RepRap ...
thingiverse
This is a cam mount for the Five33 Tiny Trainer quad, which holds the Runcam Micro camera. ... I sliced with Cura, using their tree supports, and printed with SainSmart TPU,
thingiverse
The bottom of the fin is also tapered to match the taper of the top of the poly carbonate canopy that comes with the Tiny Trainer. You can also drill a 2mm hole in the Tiny Trainer poly carbonate pod and run a 2mm x 5mm or 6mm screw up from the...
cults3d
Tail fin for the FliteTest Tiny Trainer. This "thing" was actually created cause I needed a little more weight at the tail in order to compensate the center of gravity. However, it also protects the original rear fin, which consists of a foam...
thingiverse
Canopy for the 4" Tiny Trainer The tall arms option has taller arms for thicker leds, like the hglrc one. It also has a cutout behind the right rear arm to allow a cap to stick out. Always use a cap. ... The sled is a 25.5x25.5 whoop style printed...
thingiverse
Tiny trainer V2 - battery mount Similar to the original but designed to take a longer battery GNB 720mAh 3S 100C LiHV Battery which is 71mm long and GNB 520 HV. To be printed in TPU. ... Versions: - 71x20 - this fits both GNB 720mAh 3S 100C LiHV...
thingiverse
This is an add on piece to glue to the bottom of the tail on a Flite Test Tiny Trainer. It is designed to fit over the foam piece that sticks out the bottom of the fuselage. As an added bonus it will also raise the back end of the plane up slightly...
thingiverse
Just a simple remix of a file that adds a big ring around the tiny trainer fpv cam mount. Specifically designed for the Caddx Baby Ratel Nano Cam. ... Added two more remixes with added prongs on top to allow mounting a naked go pro I am using a...
thingiverse
This is a loose remix of the original camera mount (Foxeer nano https://www.thingiverse.com/thing:4315912) for Tiny Trainer. I modified it to: - allow longer lipo to mount more forward for better CG - shifts camera a bit forward and lower to...
thingiverse
This is a replacement firewall for the FT Trainer RC airplane. I think a couple of other planes use this firewall as well but I'm not entirely sure. This screw spacing is 8mm from center and the center hole is 8mm. I have an A2212 2200kv motor that...