55 mm inches 3d models
309128 3d models found related to 55 mm inches.thingiverse
Nach Jahren war bei meinem Lieblingsrucksack der Verschluss defekt. ... Ich habe einfach die Datei von Benoit Tarrade https://www.thingiverse.com/thing:2137647 remixt und auf meine Gurtbreite von 55 mm angepasst... ...und dann gedruckt!
thingiverse
Original https://www.thingiverse.com/thing:3241700 This https://www.thingiverse.com/thing:3241700 printed cover is not suitable for 55 mm, I slightly corrected it and made two versions clean and with the Sony Alpha logo. ... Black PLA.
thingiverse
This is the f3d file for flat or cutout corners at 55 mm, plus all lengths of fill-in linear pieces. ...Happy to more more edits or if STLs are needed.
thingiverse
// ENGLISH A 55 mm knob with an insert for a M10 nut // FRENCH Une molette de 55 mm avec un emplacement pour insérer un écrou de type M10
thingiverse
This is a box for pocket watch. ...The hole is for a pocket watch of 55 mm.
grabcad
This is a 55 x 55 x 12 mm heatsink for use with graphic cards. It has an small 12 V fan, and can be installed on a PCB via two plastic push pins. ...It's useful for cooling high power LEDs, motor driver chips and other high power semiconductors.
thingiverse
Flashkill / Honeycomb protector for scopes. ...Reduces glare from the sun and protects against debris. Currently in 55.88mm diameter
thingiverse
A simple tubular parasol for 55mm lens (test on a olympus Lens). ... It has 57 mm internal diameter and need sand a little for a better adjust.
cgtrader
55 inch Samsung QLED The Frame TV. Article: QE55LS03RAUXRU The set includes legs for installation on the pedestal and legs for installation on the floor, just remove unnecessary =) Smoothing modifiers were not used. ...Polycount: 7194 Link to the...
thingiverse
It design for use with 55 mm filter to any camcorder or camera. ... It's inner diameter was 57 mm but fit with outer diameter of 55 mm filter. It has center mark for easy adjust into the center. ...
thingiverse
Увеличил внутреннее отверстие до 55 мм, что бы подходило на любой держатель. ...Прилагаю исходник в формате Фюжен 360 + step. Biggest hole (55 mm) for holder filaments of the 3d printer. ...Source in fusion 360 + step file.
thingiverse
This is case for IR filter 55 mm. The filling is felt with thickness 2mm. ...The inscription is in Czech language.
thingiverse
This is a set of simple miniature bases in sizes used in Infinity the Game (25, 40 and 55 mm). ...They have magnet slots underneath (for 5x1 and 3x1 mm magnets) and marks determining firing arcs on their sides.
thingiverse
I have designed this item to allow a easier fit of my ski boots and as shoes trainers dryer. ... It fit in a 55 mm truma heater hole., but i should be fit in other brands too.
thingiverse
v2: https://www.thingiverse.com/thing:4194963 This is a laptop stand that I made for a 30.55 mm thick laptop (the actual distance between the prongs are 31 mm. It's still a little messy, but I'm proud of it, because I made it from scratch! I...
thingiverse
4 Füße , Innendurchmesser 55 mm , 30 mm Höhe . ...IKEA Sofa
prusaprinters
Derfor skal du forstørre modellen for at kompensere for det.PLA: 100,3%PETG: 100,4%ABS: 100,8%Hvis du anvender rammerne i en 230V installationen, skal en autoriseret el-installatør i princippet risikovurdere og godkende denne anvendelse.LK laver også...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=9860 Instructions Using the following options: buckle_gap = 5 mount_lip_width = 0.2 circle_sides = 70 mount_lip_height = 0.1 buckle_width = 42 mount_height = 2 buckle_thickness = 4 mount_base =...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: approximate_number_of_teeth_on_sun = 9 number_of_planets = 5 w = 6.7 P = 45 T = 10 D = 51.7 nTwist = 1 tol = 0.55 number_of_teeth_on_planets = 7
thingiverse
This thing is made for Furniture Adjustment. ... use 3,0x16 or 3,5x16 mm screews
thingiverse
Modified from the original http://www.thingiverse.com/thing:491383 NEILV with "Agus" name. ... Scale 101% be necessary to fit in 58 mm lens cap.
thingiverse
I used 5 mm acrylic sheet, and glued two parts to get a 10 mm part, but would be better to use 10 mm sheet. This version was inpired in those designs that use magnets to fix the lower part of the shoe. If you find some change that could optimize...