5kg spool holder 3d models
350036 3d models found related to 5kg spool holder.thingiverse
5KG spool holder! V2 has 3/8 threaded rod hole for support! ... may also need to print https://www.thingiverse.com/thing:2853267
thingiverse
Ender 3 - 5kg Spool Holder Description This spool holder is designed to mount 5kg spools on top of your machine. You need to print two and place them on either side of the spool. Can be easily installed firmly without screws. ... Designed for a...
prusaprinters
Finally, a good 3.5kg spool holder! I like to print big, and a lot, so I use 3.5kg spools with a reverse bowden tube to my printer. I could not find a decent spool holder setup for these massive spools that didn't cause print quality problems. After...
thingiverse
Finally, a good 3.5kg spool holder! I like to print big, and a lot, so I use 3.5kg spools with a reverse bowden tube to my printer. I could not find a decent spool holder setup for these massive spools that didn't cause print quality problems. After...
thingiverse
This is a spool holder than can hold 2.5kg spools. I attached mine to a beam on the ceiling. ...I printed mine with PETG.
thingiverse
------------------------------------ - Print 2, one for each side of the spool - the spool holder needs to get moved in about 20mm so there is about a 5mm gap on either side of the spool ( see photos ) - Requires 4 M3 screws and 4 T-nuts - Bolts in...
thingiverse
I recently purchased a few 5Kg spools from Zyltech but soon realized it was too heavy for my Sidewinder X1 even though it does fit on the factory spool holder. So I went ahead and got a 22mm dowel from Walmart for a few bucks and created this in a...
thingiverse
Just needed a bigger holder and figured id upload it here. I bought a 5kg instead of a 3kg. ... Happy printing y'all!!!!
thingiverse
Many designs for the 5kg spools are rather weak, this design will not let you down. You will need a LARGE PRINTER for this design as it is necessarily wide/long to maintain stability. ... Warning: you will need just over 900g of filament if you...
thingiverse
Spool holder to fit the large 5kg spools with a 113mm hole uses 608 bearings. Instructions I printed 0.3mm 25% fill. You may or may not need support, I used supports as it's the inner section that...
thingiverse
I really like this style of spool holder because there's nothing to put through the center of the spool, just set the spool on top and go. This is for the 5kg Zyltech Texas size spools. It uses the same ZZ608 bearings. You will need 8 of the...
thingiverse
I needed a spool holder that was compatable with a 5KG roll of filament. Had a hard time finding one to purchase so I decided to make one. The frame is cut out of 3/8 acrylic, the pipes are 1 inch PVC cut to 8 inch sections and the caps are hot glued...
thingiverse
... rod if you feel you need extra reinforcement. ...I use this currently. Modified the items provided by original design to fit the 5kg Spools from eSUN 4-6 outline 30% infill for base 50% infill for axel Support from base for axel, no support for base
thingiverse
I stretched this to fit the zyltech 5KG spool, I also edited the existing braces to accept a 2.5 mm screw through the middle. ... Here are the 2.5mm screws I used -...
thingiverse
spool holder for a 4.5 Kg coil.~11h printing with 0.3 layers and 15% infill. ...no support needed.
thingiverse
I liked the 5kg Spool Holder by gfursu, but wanted to have an axle riding on 2 608 bearings. So i designed an adapter that fits in the slots for the old axles and can hold an 608 bearing. Lastly i added an axle and an insert for the spool to ride...
prusaprinters
I liked the 5kg Spool Holder by gfursu, but wanted to have an axle riding on 2 608 bearings. So i designed an adapter that fits in the slots for the old axles and can hold an 608 bearing. Lastly i added an axle and an insert for the spool to ride on....
thingiverse
Simple remix to fit a 256x256 bed. Good amount smaller yet just as strong. I also just made a simple plastic rod that snaps in place. ... It's as basic as it gets, but it's fast.
thingiverse
this was the original - https://www.thingiverse.com/thing:3353204 I could not add his as a remix on my page for some reason, all credit goes tohttps://www.thingiverse.com/wavexx Ijust made the wheels and railswider for bigger rolls print 4 of...
thingiverse
A remix of the the "TUSH FT - Spool Holder - Fat Tracks edition" with wider rails. Each roller still uses 1 "608" ball bearing. Note: The static load rating per 608 bearing 315 lbs, so using 4 for a 5kg roll is definitely sufficient... Print 4 of...
thingiverse
modified spool holder for additional height and 3030 mounting, without screws. ... Print with HTPLA or PETG, extra perimeters, extra top and bottom of added strength
thingiverse
Anycubic PREDATOR: it is a simple 2.5 spool holder to adapt to the standard 1 kg stirrup. Is necessary n° 4 bearing 608 , one screw and nut M8 Fix to the verical stirrup using M3 screw and nut. ... Post your make!
thingiverse
Goes in place of the stock rollers on top of the frame. ...No modifications required.
thingiverse
As there doesn't appear to be any spool holders using bearings in this formfactor which fits 5kg eSun branded rolls, I decided to modify a design and add my own touches to make it easy to switch rolls over with just two pieces. Print: 1 x frame ...
prusaprinters
Want to mount your 5lb KVP spools to the excellent Zyltech Spool holder designed for their 5kg spools?Well here you go, since the included adapters wont work as well for other brands spools I designed one from scratch and have included the step file...