6 inch dust collection fittings 3d models

this is a blastgate designed for a 6 inch hose on a dust collection system. the 2 halves will need to be bolted together with the slider in the middle. the hose attachments will need to be glued on with a super glue. please note ihave not finished...

This piece replaces the factory Y fitting on most dust collectors with a 6" inlet. This will substantially reduce the turbulence of the Y fitting and increase airflow by reducing the drag through the system, resulting in fewer clogs and better chip...

OLD FILE. ... Was requested, but I'm unsure if this is the same model that I have printed. 6-inch end is pipe size, so fits into a 6-inch hub end. ...4-inch end is hub size, to accept 4-inch pipe.

Wood Shop Dust Collection Fittings: 1: 2 1/2 inch hose to 4 inch input (hole) 2: 2 1/2 inch hose to 4 inch fitting 3: 4 inch hose to 4 inch fitting

Fitting for dust collection system for woodworking, CNC router etc

... adapter fittings. The fewer fittings, the better for DC performance. This wye is designed to connect two 4-inch branch lines off a 6-inch main line. The ends are sized like the hub end of PVC fittings and will fit 6-inch and 4-inch PVC pipe. ...

The side toward the dust collector is designed like the hub of a S&D pipe fitting, so it fits directly on the end of 6-inch pipe. The side toward the tool is designed for a good fit with the flex hose, which in turn connects to the DC port on the WW...

Coupler for 4" dust collection piping. ... I use this piping for dust collection: https://www.homedepot.com/p/Advanced-Drainage-Systems-4-in-x-10-ft-Triplewall-Pipe-Solid-4550010/100135310 No need to glue; just duct tape in place.

## Dust Collection Fitting - 6" to 2" Wye My wood shop dust collection system is designed with 6" PVC "Sewer and drain" pipe for the primary runs, but I needed to take a branch off the main run for 2" schedule 40 PVC pipe. Not finding a suitable...

Additionally, once you get up into 6 inch and bigger sizes, the fittings get expensive. These factors led to designing and printing my own fittings for the DC system. Blast gates, elbows, and wyes. I tried to design these to minimize pressure drop,...

Additionally, once you get up into 6 inch and bigger sizes, the fittings get expensive. These factors led to designing and printing my own fittings for the DC system. Blast gates, elbows, and wyes. I tried to design these to minimize pressure drop,...

I couldn't find a reasonable non-splice 6" dust pipe connector online for my dust collector, so this is a simple solution. I used a few pieces of electrical tape to add some grip. ... ID 152mm OD 158mm height 100mm

This is a fitting for a 4" dust collection hose to attach to the base of a Delta Unisaw. ... I reinforced mine with aluminum foil tape.

These are the magnets I used --> [Amazon Link](https://www.amazon.com/gp/product/B08GLS59JS/ref=as_li_tl?ie=UTF8&tag=dloud81-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B08GLS59JS&linkId=973d553a9eac5788787e3082fa499bbe) 1A – 4inch magnetic...

Set of Y adapters and blast gates for using 4 inch PVC sewer pipe as a dust collection system. I never tried printing the 4 inch blast gate because my printer is too small. Most of the blast gates are in two halves and you can weld them together...

Set of Y adapters and blast gates for using 4 inch PVC sewer pipe as a dust collection system. I never tried printing the 4 inch blast gate because my printer is too small. Most of the blast gates are in two halves and you can weld them together with...

I'm sure we've all said when buying parts for our dust collection systems " Why don't they just have a basic coupler available for that?!?!! So here it is: A SIMPLE 4" COUPLER FOR DUST COLLECTOR SYSTEMS I can't believe that there were none on...

I was making a thein dust collection setup and wanted a few magnetic connectors. I wanted to be able to remove/move the trash can easily while having my harbor freight dust collector wall mounted. I used the stock harbor freight 5 inch hose for...

Dust Collection 4-inch Port to 2.5-inch Hose Tapered Adapter Dust Collection Reducer FittingI suggest printing with these settings:Filament type: PLA (I used PLA+)Nozzle diameter: can be 0.4mm or 0.6mmLayer height: 0.3mmWall thickness: 0.6mmNumber of...

## Dimensions Overall Length: 2.25 inches Overall Width: 4 inches The STEP file is included. ... # Print Settings Material: [Hatchbox...

The ends have a 2 degree taper to allow the hose to slide on easier.The STEP file is included.DimensionsOverall Length: 2.25 inchesOverall Width: 4 inchesThe STEP file is included.Print SettingsMaterial: Hatchbox ABSVertical Perimeters: 4Horizontal...

... underside if that bothers you as it was a bit rough).  Laying on it's back I used minimal supports, under approx ½ of the base.  It seems plenty strong enough either way.  I am using several of these in my ducted dust collector setup.

... attaches to a horizontal 2x4. Tolerances aren't very tight, so it leaks some air, but it's better than the Harbor Freight ones I was using. Printed on my ender 3 with no special adjustments to any settings. They'll both fit if you angle @ 45*

I use this piping for dust collection (thinner, lighter, and cheaper than regular PVC piping): https://www.homedepot.com/p/Advanced-Drainage-Systems-4-in-x-10-ft-Triplewall-Pipe-Solid-4550010/100135310 It's a friction fit; no need to glue, just duct...

I use this piping for dust collection (thinner, lighter, and cheaper than regular PVC piping): https://www.homedepot.com/p/Advanced-Drainage-Systems-4-in-x-10-ft-Triplewall-Pipe-Solid-4550010/100135310 It's a friction fit; no need to glue, just duct...

The use of a bellmouth will improve dust collection from an open duct by an enormous margin, particularly fine dust particles.This model has been designed to fit in a standard 6" (150mm) PVC plumbing joint.  The outer diameter is 154mm, the...

4 inch to 2 inch Wye connector for dust collection, you will need a large printing area to complete this one, I designed it for my Ender 3 Max. You should add some minimal support to the bottom and print it with the 'Y' part facing upwards for best...

This is a male-male coupler, designed to fit inside a schedule 40 4" pvc pipe and connect to the inside of the larger diameter 4" dust collector fitting. The blast gate in the picture is from Woodcraft. Note this will not fit in the smaller dust...

I was in need to of a 6" to 5" (O.D) reducer for my dust collection hosing to my Jointer/Planer combo machine. I purchased a couple, but they were too flimsy, so I modeled and printed one out. 3" surface on each end for clamping. I've uploaded...

I designed this dust collection adapter to fit over the HITACHI C10FCH2 dust outlet and to interface with a 2.5'' hose with hose clamp.