6 mm conversion 3d models
574384 3d models found related to 6 mm conversion.thingiverse
Immersion-RC APEX 6" or Clone frame Longrange Conversion Files. Front mount: Pilot Seat GoPro and Micro Cam (allows mounting of a 4K Recording Cam with Straps). ...Rear mount: BN880 GPS for SMA Antenna mount with some slots to use Zipties for mounting...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: kerf = 0.3 Nut_Size = 6 DualExtrusion = Extruder1 message = 6 mm Font = write/Letters.dxf ToolOptions = 2 Tool_Length = 10
cults3d
This is a tray for the TRX 6 AMG body but can also be applied to other long wheelbase crawlers. ...It has 4 corner screw holes and an optional 5th at the top end of the tray.
thingiverse
This is a conversion kit for the Mugen MBX 6, consisting of a motor mount, a battery tray, a receiver tray and two body risers. All you have to do is cut the original dual servo mount and add some screws and velcro straps. BE ADVISED: this kit can...
thingiverse
I had problems printing this thing because the stl was saved in inch. ... A simple multiplication of the size with 254 (100% -> 2540%) gives you the mm version.
thingiverse
This offsets the conversion, so that it can be used as a hot-end cooler, and not hit the print bed. ... Rather than center the 40 mm connection in the middle, it shares a common side with the 80 mm connector.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47842 Instructions Using the following options: Tool_Height = 5 message = 6 MM STINO Nut_Size = 6 Tool_Length = 13 Font = write/Letters.dxf
cults3d
This full body 6 mm sprinkler is ready for use after custom cutting a slot for the desired arc of spray up to 270 degrees. The marker on the hex face denotes the direction of spray where you should begin cutting. ...Print upside down for best results.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: shaft2 = 5.8 shaft1 = 5 gap = 0.3 offset = 2 nut = 5.8 thickness = 4 bridge = 0.3 length = 30 washer = 0 wall = 1.6 boltHead = 6.7 trap = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: length_above_grip = 60 narrowing_ratio = 0.16 hook_length = 5 grip_slope = 5 narrowing_slope = 20 throat_angle = 10 grip_length = 20 diameter = 6...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: resolution = 0.5 non_thread_length = 0 socket_facets = 6 head_height = 3 non_thread_diameter = 0 drive_type = slot nut_type = normal slot_depth =...
thingiverse
... of http://www.thingiverse.com/thing:1298521 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298521 Instructions Using the following options: pipelarge = 36 midsection = 10 $fn = 1000 wall = 4 pipesmall = 6 end = 20
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=454702 Instructions Using the following options: tubing_squish_ratio = 0.5 tubing_od = 6 tubing_wall_thickness = 2 nTwist = 1 allowed_overhang = 0.5 number_of_planets = 4...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: resolution = 0.5 head_type = hex nut_type = normal slot_width = 1 outer_diameter = 10 nut_height = 6 nut_thread_outer_diameter = 9 type = washer...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options: ShaftDiameter = 10 HoleDiameter = 6.5 HoleDepth = 10 Pointer2 = 0 Pointer1 = 0 CapType = 1 TimerKnob = 0 RingMarkings = 10 TaperPercentage = 20...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=454702 Instructions Using the following options: tubing_squish_ratio = 0.5 tubing_od = 6.5 approximate_number_of_teeth_on_sun = 9 number_of_planets = 4 tubing_wall_thickness = 2 w = 3.7 P = 55 T...
thingiverse
This is conversion kit for airboat. ...Uses 2205 or similar motor with two blade 6 inch propeller. ...More efficient thatn 5 inch and gives more thrust.
thingiverse
Assembly: Clip the 6 Player Conversion over the base from the bottom. Since the print was semi-flexible, it can deform enough to clip over the angled base. The vertical ridges hold it perfectly in place. Attach the 6 paddles. Be careful though, it...
thingiverse
Cutting jig for the harbor freight 6" Cut Off Saw. ...Fits 308 Win or 6.5 Creedmoor cases. https://www.harborfreight.com/power-tools/power-saws/cut-off-saws/6-in-55-amp-cut-off-saw-61204.html
thingiverse
------ Strengths : Very versatile (can handle most of the small springs) Flexible as the handle is designed to receive different size winder (6 & 8 mm by now, but we can redesign the whole thing to achieve other diameters) Easily swappable (you just...