60 tooth sprocket 3d models

23 Tooth #60 Roller Chain Sprocket 1.5" Bore Add keyway and set screws as you desire

5.25 x 6 bolt hole circle. Common for many karting applications. ...

15 tooth sprocket

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_dia = 0 additional_tooth_depth = 0 no_of_nuts = 0 nut_angle = 0 pulley_b_ht = 0 profile = 10 additional_tooth_width = 0 pulley_b_dia = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_dia = 3.2 nut_shaft_distance = 1.2 profile = 2 additional_tooth_width = 0.2 nut_angle = 90 additional_tooth_depth = 0 m3_nut_hex = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: retainer_ht = 4 pulley_b_dia = 25 motor_shaft = 6.37 additional_tooth_depth = 0 profile = 6 no_of_nuts = 1 nut_shaft_distance = 1.2 m3_nut_depth =...

We are using this piece as a rough estimation of a 10 tooth sprocket from andymark

... scale models, one is limited to a small selection of sprockets for the larger style tread, as this will usually determine the scale. ...This custom 8 tooth sprocket fills a gap in the current selection between 6 tooth sprockets and 10 tooth sprockets.

Model of this sprocket:http://www.amazon.com/Flying-Horse-Tooth-Drive-Sprocket/dp/B00KO5VKWS?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o02_s00

This is a 15 x sharp toothed Sprocket with a press fit bearing on center in stainless steel c/w with two rubber seals two renders shown in Photoview360 whilst one is KEYshot4 in an anodize aluminium variant.

Lynxmotion Track Sprocket - 6 Link

Fits with "Spline", required spacers in between each sprocket

Model of this sprocket:http://www.amazon.com/Sunlite-1-Piece-Chainring-32-52t/dp/B000AO9ZVQ?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00

526 - Sprocket 25 Tooth Gear

4 60-tooth turbines - 60

Sprocket, 17 Tooth, 0mm Offset Material: ADI Grade 4 (BHN 388-477)Bolts up to this hydraulic motor...Motor, Hydraulic 2-Speed

A 60 tooth gear that can be used for robotics

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: motor_shaft = 10 nut_angle = 90 idler_ht = 1.5 m3_nut_flats = 5.7 m3_nut_depth = 2.7 nut_shaft_distance = 1.2 no_of_nuts = 1 idler = 0 retainer_ht...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_dia = 3.2 m3_nut_hex = 1 motor_shaft = 5 nut_shaft_distance = 1.2 idler_ht = 1.5 m3_nut_flats = 5.7 retainer = 1 additional_tooth_depth = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: additional_tooth_width = 0.2 nut_shaft_distance = 1.2 m3_nut_depth = 2.7 pulley_b_ht = 9 m3_nut_hex = 0 retainer_ht = 1.5 idler_ht = 1.5 retainer...

Modified NateTG's 60-tooth acme worm gear by adding center bore for 5mm shaft, M3 screw holes, trimming down the gear edges, converting original STL file inches to mm, and upscaling 1% so the print would better match a surplus Boston Gear worm of 32...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_dia = 20 no_of_nuts = 1 idler = 0 motor_shaft = 20 m3_nut_hex = 1 retainer_ht = 1.5 additional_tooth_width = 0.2 pulley_b_ht = 8...

12 tooth sprocket for standard bicycle chain 54mm Diameter with 14mm nut recess

​12 tooth sprocket for standard bicycle chain​ 54mm Diameter with 14mm nut recess https://youtu.be/XC6OF7xqSWA

not so standard chain sprocket

An odd sized sprocket for custom use

Rokenbok X2 4 Tooth Drive Sprocket These designs are owned by Rokenbok Education (http://www.rokenbok.com) and published under license by kid*spark (http://www.kid-spark.org), a nonprofit corporation, for nonprofit and educational uses. Drawings of...

This part was used in the building of this:https://solar1.net/drupal/plasma_cnc Instructions This sprocket will hold two 22mm VBX bearings (Skate size) the inside (shaft) diameter is 8mm You may have to press the bearings in. ...I used a bench vise to...

Replacement for gas motor scooter wheel sprocket. Print Settings Printer: CTC Rafts: No ...

... to remove it completely. My Anycubic S left me some polishing work to fit the metal counterpart into sprocket, but so far it works perfectly. ... If you want to play more with it, here's my source: https://www.tinkercad.com/things/2ZzeCO22TgL