60mm fan guard 3d models
136759 3d models found related to 60mm fan guard.thingiverse
60mm fan guard with side openings to avoid pressure drop on output dimensions: 60 x 60 x 25
thingiverse
60mm fan guard, minimal material, rounded grille, maximum airflow 80mm version https://www.thingiverse.com/thing:4727422 92mm version https://www.thingiverse.com/thing:4727426
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_holes_d = 7 solid_outer_border = 1 outer_roundness = 50 mesh_kind = radial_poly mesh_offset = 68 mount_hole_width = 50 fan_side_length = 60...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_clearance = 1 mount_hole_width = 50 mesh_density_ratio = 98 fan_side_length = 60 mesh_thickness = 1 mesh_holes_d = 10 mesh_kind = hex...
thingiverse
My goal was to design a fan grill that would add very little noise to a very quiet Noctua fan. The blades in the grill are aerodynamically shaped (upside down teardrop) and there are no sharp edges to minimize the additional noise created as the air...
thingiverse
A 60mm fan guard with the added benefit of pins negating the need for screws. -------------- Customized version of http://www.thingiverse.com/thing:263573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=263573...
thingiverse
Customized version of https://www.thingiverse.com/thing:128718 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=128718
thingiverse
Customized version of https://www.thingiverse.com/thing:128718 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=128718
thingiverse
Customized version of https://www.thingiverse.com/thing:128718 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=128718
thingiverse
A sturdy fan cover for a Noctua NF-A6x25 60mm fan. ... Posts are 6mm tall to prevent noise.
thingiverse
60mm Fan guard for EIBOS 3D Filament Dryer CYCLOPES, but can be used for any other fan :) After the fan grill of my EIBOS Filament Dryer melted, I had to replace it. I printed with ASA plastic as it has the greatest heat resistance. ...
prusaprinters
60mm Fan guard for EIBOS 3D Filament Dryer CYCLOPES, but can be used for any other fan :)After the fan grill of my EIBOS Filament Dryer melted, I had to replace it. I liked the design of <a...
thingiverse
... a fan guard too close to the fan sometimes causes an increase in noise. See my other Noctua parts: * [40mm Fan Guards](https://www.thingiverse.com/thing:3684120) * [Noctua 60mm Minimalist Fan Mount](https://www.thingiverse.com/thing:3107913)
thingiverse
Customized version of https://www.thingiverse.com/thing:2133477 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2133477
cults3d
Customized version of https://www.thingiverse.com/thing:2133477 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2133477
thingiverse
Customized version of https://www.thingiverse.com/thing:2133477 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2133477
thingiverse
- This item is particularly useful for high speed, high static pressure fans; where the first time you stick anything into the spinning blades will almost always be the last time. - As always; assumes a 0.4mm nozzle. ...Layer height is fairly...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 you need to drill the holes yourself Instructions Using the following options: solid_outer_border = 1 mesh_kind = hex mount_hole_d = 0 mesh_holes_d = 5 mount_hole_width = 0...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_density_ratio = 100 mount_hole_d = 3.4 mesh_kind = hex mesh_thickness = 1 mount_hole_width = 50 mesh_offset = 23 mesh_clearance = 1...
thingiverse
60x60mm High Speed Fan Guard My Nidec© UltraFlo® 60x60mm fan was too noisy with a stock finger guard so I whipped up this design with better airflow. 15db lower sound with this design. ... Still noisy but tolerable.
thingiverse
fan guard for 60mm fan with pegs that snaps into screewholes
thingiverse
####GIRO - 60mm Fan Cover / Fan Guard#### ####General#### This is a simple fan cover I created for my printer which uses a 60x60x25mm cooling fan for the mainboard. This fan cover needs four M4 screws and four M4 nuts. These are neccessary to mount...
prusaprinters
GIRO - 60mm Fan Cover / Fan GuardGeneralThis is a simple fan cover I created for my printer which uses a 60x60x25mm cooling fan for the mainboard.This fan cover needs four M4 screws and four M4 nuts. These are neccessary to mount it onto a 60mm...
thingiverse
This is a remix of rawyal's very clean Punisher fan cover for 60mm fans.
thingiverse
A remix of [https://www.thingiverse.com/thing:3017633] I already used the above thing on a 40mm fan for my printer setup and wanted a matching design for a couple of 60mm fans that I use so I designed my thing entirely based on the above thing. ...
cults3d
A remix of [https://www.thingiverse.com/thing:3017633] I already used the above thing on a 40mm fan for my printer setup and wanted a matching design for a couple of 60mm fans that I use so I designed my thing entirely based on the above thing. ... Lots...
grabcad
Just for practice.If you find this model useful, please share your support by providing a like in return. ... This keeps sharing fun.