6x4 index cards 3d models
81511 3d models found related to 6x4 index cards.thingiverse
A simple 6x4 inch index card holder remixed from steve220's index card and pen holder. ...The inside is 15mm wide.
thingiverse
Designed for holding 6x4" index cards which are sliced into thirds. Has a slot for viewing current notes and a spacer card for breaking the top and bottom slot up. Printing: Printed at 20% infill, brim adhesion and with the model flat. Printing...
thingiverse
This is a index card holder that is convenient and easy to remove an index card. ... I have big fingers and this design provides an very easy access to the cards.
thingiverse
Simple remix of **Index Card Holder** by **HamOP.** I resized the models to fit more common US 3x5 index cards, as well as adding a hex grid to the bottom to allow for faster prints with less filament.
thingiverse
Index for Flash Cards. Format A7. I have created these for my son for his vocab cards. ...
prusaprinters
Index for Flash Cards. ...Format A7.I have created these for my son for his vocab cards. In my case works best with front side down and this configuration:Printed in PLALayer 0.20 mmInfill: 100% Top/Bottom fill pattern: Octagram...
prusaprinters
Index for Flash Cards. Format A7.I have created these for my son's vocab cards. ...Also check out the corresponding <a href="https://www.printables.com/de/model/143995-shutter-box-in-two-sizes">shutter boxes on printables.</a></p><p>In my case it works...
thingiverse
A Sorting box with 9 Index Cards. Box 15,4 x 12,2 cm designed to hold DIN A6 Paper size (1/4 DIN A4) You could scale it to hold other sizes. Printing Time on my Ender 3: Box ca. 9h Per Index Card ca. ...1,5h
prusaprinters
Index cards box for DIN A8 cards. ...200 cards fit into it.
thingiverse
Index cards box for DIN A8 cards. ...200 cards fit into it.
thingiverse
Index cards box for DIN A7 cards. ...200 cards fit into it.
prusaprinters
Transport box for Index cards A7 105mm x 74mm. Printable without support. Use a piece of filament as hinge-pin, but you might have to push a metal rod or wire through first to clean up the channel. Print instructionsNothing special, just print, no...
thingiverse
Remix for 3"x5" index cards of DIN index card box by @TheBlackJack
thingiverse
Simple trays for index cards, configurable to card size. I have one of these in every office and stocked with 3x5 index cards. Also handy in quarter-sheet size (4.25x5.5). ... STL files for each size are included, plus the OpenSCAD source.
thingiverse
The box can hold up to 60 cards with still a little bit of space. The lid is put on and taken off with slight pressure of the thumb finger nail against the side of the box, where the hole is while pulling or pushing the lid with the other hand. The...
thingiverse
* This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7zpKHAMDSAw * Need a small box to keep my small index cards, so I quickly designed one in `tinkercad`. ... * The small index card is from Daiso, size: 91mm x 55mm
grabcad
An indexing device to allow for timing in a mechanical device (I'm not sure what the particular device that is though).
thingiverse
Customized version of https://www.thingiverse.com/thing:537516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=537516
thingiverse
Customized version of https://www.thingiverse.com/thing:2006468 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2006468
thingiverse
Customized version of https://www.thingiverse.com/thing:3263783 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3263783
thingiverse
Customized version of http://www.thingiverse.com/thing:69265 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69265
cults3d
Here is a index card box for up to 400 DIN A7 index cards with the size of 10,5 x 7,4 cm. There is a little gap in the front so you can insert a piece of cardboard to label it. If you have questions or problems feel free to cantact me so i can...
grabcad
Bayonet 6X4 for SVD, AK, G36. Штык-нож типа 6X4. ... <A href="Johar Palacita">Johar Palacita</A>'s model <A href=snayperskaya-vintovka-dragunova-s-v-d>Snayperskaya vintovka dragunova (s.v.d)</A>, <A href="Zeljko...
thingiverse
I also did a control test with a 6x4 store bought prop. This prop exerted 1.8lbs at max rpms. Part of this adventure has been getting the print quality perfect. It took about 5 or 6 attempts but I finally can print the prop with minimal cleanup...
thingiverse
Customized version of http://www.thingiverse.com/thing:797089 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=797089 Instructions Using the following options: thk = 3...