70mm stem 3d models
15693 3d models found related to 70mm stem.grabcad
Easton Haven 70mm stem.Modeled with Solidworks, rendered with Keyshot.
grabcad
Doing a project involving a Mountain bike stem. ...So I modelled up mine to start with.Blends caused some geometry errors with the end cap, but for my purposes it's fine.
grabcad
My first non-school work. ...I started a few weeks ago in school with rhino and i'm a fan of bikes so i made a Stem. ...I hope you like it!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: width = 50 length = 100 edge = 5 line2 = Summit line1 = STEM 3/19 holeRad = 5 tagThickness = 10 tagH = 19 radius = 15 Font = write/orbitron.dxf...
thingiverse
Some stems are different profiles, but this worked on an Uno 7 70mm stem, as well as Deda Zero stem. Size 8-32 and hex nut fit ok. Put foam tape on the bottom and top in the center where the plastic meets the stem if possible, to avoid the clamp...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: line5 = line4 = line3 = line2 = line1 = STEM border_thickness = 3.6 bar_length_trim = 0 outlineextruder = extruder1 font_outline_width = 0.5...
prusaprinters
Two piece mount to attach to road bicycle stem. Some stems are different profiles, but this worked on an Uno 7 70mm stem, as well as Deda Zero stem. Size 8-32 and hex nut fit ok. Put foam tape on the bottom and top in the center where the plastic...
cults3d
A pallet of 70mm x 70mm, is separated in all its components, you just have to print them as the file says "together", and then glue them with some adhesive. and then glue them together with some adhesive. In case you want to print parts separately,...
thingiverse
Customized version of https://www.thingiverse.com/thing:487090 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=487090
thingiverse
Customized version of http://www.thingiverse.com/thing:1060283 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1060283 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:487090 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=487090
thingiverse
70mm gear built in solid-works. This gear was not built for purposes other then visual and artistic. ...Not per drawing, and will probable not fit anything.
thingiverse
Dimension 70mm, axis 8mm, works with M8 nut (cap nut looks better :) ) Two versions available: spatial and easier for printing flat version. ...Spatial version has included in the project necessary support for printing, this hexagonal support has to be...
thingiverse
In order to get my cables through it I used a 70mm round drill. However that is a bit wide, so I designed a cover for it which covers the whole, but leaves space for a small power connector. The whole is roughly 4,5cm wide and 2,5cm high. It is...