75mm round base 3d models
491141 3d models found related to 75mm round base.thingiverse
Made with the source from a round base customizer, which didn't work for me.
myminifactory
... Pit base can be used for huge creature in your boardgame. The Primal Pit will be part of the Pit Fight Base Bundle (other 2 decorated 75mm bases included) will be available in the kickstarter campaign: The Admiral Apocalypse's Project The Admiral
thingiverse
Customized version of https://www.thingiverse.com/thing:1112237 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1112237
thingiverse
... to use as a Kraken in Mantic's Armada game. ...So I took nexnox's benchy wave stand, compressed it, stretched it, cut it to 75mm square and cut a hole in it for the 50mm round base of the deep madness figure. ...Printing now so let's see how it went!
myminifactory
75mm base with brickwork design for use with models. ...Perfect fit for huge creatures in dungeons & dragons.
thingiverse
This is a Remix of Marius Hornberger Flexible Dust Collection Segment. ... It's a base to be screwd on an even surface. ...
thingiverse
Painless dough cutter round 75mm Full blog post: https://nerd-corner.com/round-edge-cookie-cutter/ https://www.youtube.com/watch?v=x4MywfAbMEI https://www.youtube.com/watch?v=WMYb1sHRTm4
cults3d
Painless dough cutter round 75mm Full blog post: https://nerd-corner.com/round-edge-cookie-cutter/ https://www.youtube.com/watch?v=x4MywfAbMEI https://www.youtube.com/watch?v=WMYb1sHRTm4
thingiverse
I made a simple round base for figures I've printed. ... Comes in 75mm x 75mm x 3mm but can easily be scaled to accommodate larger or smaller figures (if you uniform scale then remember to not go too thin on the Z scale however).
cults3d
75mm decorated miniature base for undead miniatures & armies. ... The model has a full cut on the underside to save resin Pre- & un- supported model included
thingiverse
... located here https://www.thingiverse.com/thing:1081926 I created this as I am using a proxy for my Northern Alliance Frost Giant and i would like to keep the miniature base size the same. I found that 75mm 75mm square bases where not common.
thingiverse
The round part fits my existing 3" galvanized easily, which I want because the current parts are not necessarily in great shape (I did not want to fight with a tight fit.) The rectangular part fits snugly onto my rectangular vinyl downspouts. This...
thingiverse
This is a 25mm round base that is 3mm thick with an offset for a 15mm X 2mm base to sit into it. There is also a 6.75mm X 1mm cutout for a magnet. ...The bottom of the base measure 25mm and the top measures 24.75mm so there is a very slight taper.
myminifactory
75mm decorated miniature base for undead miniatures & armies. ... The model has a full cut on the underside to save resin Pre- & un- supported model included
thingiverse
75mm base medium frame token tray for use with the tabletop game Gamma Wolves by Ash Barker (published by Osprey Games) Unsupported, flat print, and supported versions included.
thingiverse
75mm Square Base with 1/4inch inserts for magnets. ... There are two versions included, one with mitred edges and one with square edges.
thingiverse
75mm Casting Base with center hole for 3/4″ mandrel. Sized for Snap Ring casing 75mm casting tubes. OD of the base is 2.52″. Also has 1/4″ hole in the base for insertion of a rod to ease removal from cast propellant. ... Version for both center and...
thingiverse
ACC Calibration Base for any 65mm or 75mm or 85mm size whoops. Recommend to print 50mm height one, more stable and less material. The 75mm height one if you used stiff USB cable. This base can be used as platform to calibrate accelerometer using...
cults3d
ACC Calibration Base for any 65mm or 75mm or 85mm size whoops. Recommend to print 50mm height one, more stable and less material. The 75mm height one if you used stiff USB cable. This base can be used as platform to calibrate accelerometer using...
thingiverse
https://www.thingiverse.com/thing:2909709 I focused on the 75mm size because the smaller bases tended to be mostly filled by the pre-cast bases from Reaper Bones minis, with the small gaps more easily filled in with normal basing methods. For best...
prusaprinters
Here's the set of inserts I created for the 75mm bases I previously uploaded. https://www.thingiverse.com/thing:2909709 I focused on the 75mm size because the smaller bases tended to be mostly filled by the pre-cast bases from Reaper Bones minis,...