760 mmhg 3d models
945 3d models found related to 760 mmhg.grabcad
Vacuometro 0 -760 mmHg, marca Fielder NBR 14105-1 vacuum gauge 0 -760 mmHg
grabcad
Representação de manômetro, diametro como 6"0 a 760 mmhg
thingiverse
Customized version of https://www.thingiverse.com/thing:5392290 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5392290
thingiverse
Same as V2 - Airsoft Air rifle silencer but with Press fit to Pumpmaster 760 barrel without front site.
thingiverse
A Crestron TSW-760 table stand with openings for back or bottom cable entry. An additional opening in the back was made to make support removal easier. ...Autocad 3D file is included.
thingiverse
Mount any picatinny compatible accessory to your Crossman 760 Pumpmaster! Flashlight, red dot and IR attachment shown in photo. In cura, turn on supports and set angle to 89% to get support in the relief channel. No other support is needed...
thingiverse
A small Funnel for filling BBs into the Pumpmaster 760 this funnel easily locates on the the pivoting door on the side of the Pumpmaster. My print is bottom less to save time, you can print it with bottom layers if you wish. ... Have fun and upload...
thingiverse
Simple muzzle brake/compensator for the Crosman Pumpmaster 760. It is for aesthetic purposes only and isn't functional. The little line across the side allows you to see down the ironsights and actually be able to aim. To take off the plastic piece...
thingiverse
This sun shield / visor is designed to fit on a Garmin 760 GPS, which has a 7-inch diagonal screen. There is a notch at the bottom to accommodate the (optional) RAM mount. I've had good luck attaching this with 3M double sided foam tape. Designed in...
thingiverse
But it didn't work for me it was much too loose the pellets fell right through the clip and the clip fell right out of the pump master 760. I redesigned the clip with the advantages of 3D printing in mind. My design is much tighter fit and has a...
thingiverse
You are looking at a Hexacopter with motor to motor distance of ~ 760 mm. It was designed from scratch in Sketchup and the frame was 3D printed on Ultimaker2 with ColorFabb's PLA filament. Word of Warning: Multirotors are extremely dangerous...
grabcad
My attempt at replicating the wonderful Mission 760 Speaker on CREO, later rendered on Keyshot.See the in action in the linked video.Let me know what you think!Instagram @jw.pde
cgtrader
3d building 760 3D ModelsHigh detailed 3d building.Previews were rendered with vray mat and light.The file has all lightning setup and texturing ;multi layer phososhop PSD file included
thingiverse
... driver weight), so the printing settings are depends on you and your needs. I've printed mine like mentioned and this seems to be very-very massive. I'm not fully sure if this fits with all the seats in the series, mine is a 760 with textil seats.
thingiverse
The Dell OptiPlex 760 (and possibly other Dells) were made before SSD's were mainstream and thus the OEM caddy for the hard disk is purpose made for the big old bulky 5.25 inch hard disk drives. I found that a number of 5.25 inch to 2.5 inch caddy...
prusaprinters
The Dell OptiPlex 760 (and possibly other Dells) were made before SSD's were mainstream and thus the OEM caddy for the hard disk is purpose made for the big old bulky 5.25 inch hard disk drives. I found that a number of 5.25 inch to 2.5 inch caddy...
thingiverse
Customized version of https://www.thingiverse.com/thing:1287275 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1287275
thingiverse
Customized version of https://www.thingiverse.com/thing:1287275 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1287275
grabcad
Schaltschrankfilter für Mazak VTC 760 Cfür Standard Filtervlies ca. ...11mm StärkePLA 0,2mm Layer
cgtrader
... width-2686, height -3680mm Inside, too, made. ...All signed are grouped and displayed to zero. Railway carriage 81-760 https://www.cgtrader.com/3d-models/vehicle/train/railway-carriage-81-760 Archive includes: _2011.max / _2009.fbx / maps/ _.mat/_obj
cults3d
... aera 760 cradle model were designed for made with 3D printer. ... It consists of 3 parts, and to install one using glue will be needed. The cradle uses standard aera 760 docking connector, so it is possible easy install and remove GPS from aircraft.
cgtrader
Subway train 81-760 / 761 Oka Dimensions: length-20120, width-2686, height 3680mm Inside too made. Doors separate objects. All signed grouped and displayed to zero. ...Archive includes: _2011.max / _2009.fbx / maps/ _.mat/_obj
myminifactory
Vovlo VNL 760 True 1/64 scale. No supports needed. All parts oriented ready to print. Working wheels. Assembly instructions included. For best results print at 0.1mm layer height. Wheels are attached using #17 straight pins easily found locally or...