8 4 mm to inches 3d models
2531089 3d models found related to 8 4 mm to inches.cults3d
This is adapter for 3/4" standard water pipe to 30 mm diameter pipe, that I use in my projects.
thingiverse
This is adapter for 3/4" standard water pipe to 30 mm diameter pipe, that I use in my projects. Instructions Print with high quality (I printed 0.1 mm per layer) to get fine female thread. This part designed to be used with 3 types of vacuum...
thingiverse
Collect three vacuum lines - from 40 mm, 2 inches, 2 and 1/2 inches to 4 inches Main part test and print in ASA - (0.6mm. 255C. 115C. 60% in fill, 15 % Fan, CURA DRAFT- 0.2mm lh) Feel free to support my projects!
thingiverse
The outer edge is 10 inches and each outside square edge is one inch smaller down to 4. The empty spaces are 3mm to easily accomodate her rolling cutting tool (looks like a pizza cutter). I don't know much about quilting but hope this helps someone...
thingiverse
Hex bit to square adapter. ...I use it with my Bosch IXO.
thingiverse
I was when I had already 4 different roller handles and ended up needing a 5th one for the new rollers we bought. So I just made end caps to hold rollers on smaller sized handle's (smaller diameter rods). They take ~5 to 11 min to print. Usage :...
pinshape
I had to make this reducer when installing a bathroom ceiling fan. ...The fan exit was 4 inches dia and the hose was 3 inches dia. ...So I printed this to fit.
thingiverse
I created this spacer to mount my usb charging port to my handlebars since all the good mounts that I've found so far are for 1" bars and my old Kawasaki KZ305 has 7/8" bars. The mount I was inspired to remix this from is probably one of the...
thingiverse
It is a fan duct dedicated to various application, but it's main purpose is to replace and/or extend a traditionnal 120mmx120mmx38mm fan to a 4 inches piping, such as a 4 inches blower fan, etc. It is designed to fit with the same screws used with...
prusaprinters
Annoyed by all the different paint roller handle sizes? I was when I had already 4 different roller handles and ended up needing a 5th one for the new rollers we bought. So I just made end caps to hold rollers on smaller sized handle's (smaller...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=987604 Instructions Using the following options: Bolt_diameter = 3.1 Total_height = 25 Lower_shaft_D_depth = 4.5 Nut_diameter = 6.6 Num_spiral = 7 Lower_shaft_dia = 4 Nut_position_tweak = 1...
thingiverse
5 mm motor shaft and 8 mm screw coupler. ...Print Settings Printer: NuBBoT
thingiverse
... project and i tought maybe more people needed it. THIS is not a Z-Axis Coupler. There are a lot on Thingiverse already. This coupler is for a 2.5 mm Motor to a 8 mm rod. Therefore please check before printing if this is what you need. ...
thingiverse
Prusa Coupler 5mm to 8 mm more easy to print more robust Print Settings Printer Brand: RepRap Printer: CTC Prusa i3 Pro B Rafts: No Supports: No Resolution: 0.1 Infill: 20 Post-Printing How I Designed This Draw in OnShape public model:...
thingiverse
Prusa Coupler 5mm to 8 mm Print Settings Printer Brand: RepRap Printer: CTC Prusa i3 Pro B Rafts: No Supports: No Resolution: 0.1 Infill: 30 How I Designed This Draw in onshape public model:...
thingiverse
This is a simple three spoke spool hub for adapting a 75 mm diameter reel to an 8 mm spool rod. The design allows for a bit of flex or bow to fit snug on both sides of the spool. Spools are not exactly the same diameter on both sides so one side...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: nut = 5.5 boltShaft = 3 offset = 2 trap = 2 boltHead = 5.5 washer = 0 thickness = 4 shaft2 = 7.8 shaft1 = 5 wall = 1.6 length = 30 bridge = 0.3...
cults3d
Modified to allow vented connection to 4" dryer hose pipe for use with a custom airbrush paint booth. ...Left the wider secondary exterior ring to allow for good overlap seal using HVAC reflective tape.
thingiverse
Modified to allow vented connection to 4" dryer hose pipe for use with a custom airbrush paint booth. ...Left the wider secondary exterior ring to allow for good overlap seal using HVAC reflective tape.
thingiverse
[en] coupling 5mm to 8mm for 3D printer Z-axiz [ru] Муфта 5 на 8mm для 3D принтера ось Z
thingiverse
Stopperball or grabbing ball for Kitelines. ... Diameter 18 mm Hole 8/4 mm
grabcad
Aluminium Stepper Motor Shaft Coupling Coupler 8 mm to 6,35mm(1/4"). ...Acoplamento de aluminio 8 mm para 6,35mm(1/4").
thingiverse
The marking on this set is in inches (hence : 3/4, 5/16...) Sizes : 1/4" - 5/16" - 3/8" - 7/16" - 1/2" - 9/16" - 5/8" - 11/16" - 3/4" Estimated Print time @ 70mm/s : single bit : from 1 to 5 mn small set (1/4" to 1/2") : 15 mn big set (9/16" to 3/4")...
thingiverse
Just bought an aquarium air pump to build a DIY air assist system for a laser engraver. ...However there was no adapter to go from the 8mm hose to the 4 mm one. ...Commercial ones are about 95 cts each, here PETG 100% infill costs about 3 cts :)
cults3d
Just bought an aquarium air pump to build a DIY air assist system for a laser engraver. ...However there was no adapter to go from the 8mm hose to the 4 mm one. ...Commercial ones are about 95 cts each, here PETG 100% infill costs about 3 cts :)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=148722 Instructions Using the following options: object = 1 tip_diameter = 4.8 pen_thickness = 7 tolerance = 0.2 inner_diameter = 3.4 inner_length = 140 word = Bonjour lid_length = 30...
prusaprinters
... out of an IKEA Stuva cabinet. Click here to view my collection. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2 mm Layer Height Infill: 100% Filament: DAS FILAMENT PLA Grey Category: Household