80 20 aluminium 3d models

ALUMINIUM PROFIL 80 X 80

T-slot profile 80/20

Aluminium profile 20.20

ALUMINIUM PROFIL 80 X 40

Aluminium profile 20 series

Just some guides I made for 20 x 20 Aluminium. I used them in a project to line things up and test ideas out. Not really for support as they would not be very strong. ...Uploaded as maybe some use to someone else.

80/20 END CAP

The brackes hold the 20mm x 20mm Aluminium section together. They are a tight fit, so you have to slightly shamfer the ends of the aliminium to start it off and then hammer it into place. ... You will need a 5mm drill and some 5mm screews and nuts to...

holds a keyboard on to 80/20

80/20 standard unit profile extrusions basic tool box

A right angle 80/20 14060 connector. ...I use these with my 20 series extrusions.

A right angle connector from 80/20. This is product number 14057. ... Used with 20 series extrusions

I use this to keep my wires inside the grooves of the 80 20 extrusion.

Feet for Ender 3 Pro, but should fit any 80/20 extrusion.

Aluminum extrusions from 80/20 inc. Model 2020, measure 20mm by 20mm. ... Extrude to your needed length.

Small connector that link 80/20 shafts together. ...It can also be operate in vertical movement with the connector holding both the shafts.

80/20's 40 mm aluminum framing extrusion. ...40mm X 40mm Ultra-Lite T-Slotted Profile - Four Open T-Slots Part Number: 40-4040-UL

Corner bracket for connecting 80/20 10 series extrusion. Depending on your printer, the fit is pretty tight. ... You may not even need to screw it in.

A foot I designed for some shelving out of 80/20 extrusion I designed. ...it's faIrly rugged and can be made without supports.

80/20's dual 40 mm aluminum framing extrusion. ...40mm X 80mm Ultra-Lite T-Slotted Profile - Six Open T-Slots Part Number: 40-4080-UL

This is a T-nut designed in Blender for use in 1.5" 80/20 rail. ... Updated 7-6-18: included pre-tapped versions M8-1.25 and 1/4-20

Lighting: Good 80-20: Good Cheap Chinese COB arrays: Good This thing: Triple Good These snap on and screw on to 80-20 extrusion, and hold COB LED strips from Banggood. ...Great for easily adding lights to a thing, or making an industrial lamp.

80/20 Aluminum extrusion used to make "erector set" assemblies, fixtures, workstations, etc. Other versions are available online but needs to close the loop on all entities before extrusion is possible. ...Drawing 80/20 parts is time consuming, so I...

80/20 Aluminum extrusion used to make "erector set" assemblies, fixtures, workstations, etc. Other versions are available online but needs to close the loop on all entities before extrusion is possible. ...Drawing 80/20 parts is time consuming, so I...

... it worked well. The bolts I used were from 80/20 - they are the bolts from the 10 series standard end fastener. The nut is the economy T-Nut. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6vT7ET4nLfA

These are 80/20 linear bearing plates that I designed and used for my First Tech Challenge (FTC) robotics team. One file has the slider plate without the bearing pad, as you can purchase the bearing pads yourself on Amazon and they work much better...

This is a Bracket to hold a M18 Sensor to 80/20 1.5" x 1.5". I printed on Makerbot Replicator 5th Gen Standard with Raft and Supports. ... When the support material is taken out of the sensor holder the slight left over material lets the M18 sensor...

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: hingeFillet = 3 interiorHeight = 20 rimInset = 0.6 sidewallWidth = 1.1 interiorWidth = 80 interiorFillet = 1 hingeLengthScale = 1.1...

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: interiorFillet = 5 sidewallWidth = 1.1 hingeLengthScale = 1.1 hingeThickness = 0.3 interiorLength = 65 tabSize = 1 interiorHeight = 20...

The actual 80/20 extrusion bar is 10 inches, thought process is the bottom can be cut off in your slicing software to what ever length you want. Everything is designed around 1/4-20 bolts except the bearing slide is meant to use 3mm to lock it in...