80 20 racing rig 3d models

... a simple headphone hook I made based loosely off the design of the Trak Racer hook. ... I printed it at 20% infill and it seemed perfectly fine to hang headphones off. I wouldn't hang a heavy VR headset off it. ...But for light headphones it does fine.

Sim Racing Rig constructed with 80/20 aluminum extrusions. ...Shown with Logitec G27 components and racing seat found here on GrabCad.

Simple twist in cable holder for 80/20 rig

T-slot profile 80/20

This is my take on a sim racing rig

A rig to hold the Turbo Racing chassis in place. ... Youtube clip on it: https://youtu.be/uLn0kqGJ5W0

Sim racing setup I built based off my own design

... printing this design as a life-size model if you have a 3D printer the size of a two-bedroom apartment. ...I purely posted this as feedback as I am planning to build the frame out of steel. If there's anyone who knows about building sim rigs.Thank you

80/20 END CAP

holds a keyboard on to 80/20

80/20 standard unit profile extrusions basic tool box

A right angle 80/20 14060 connector. ...I use these with my 20 series extrusions.

A right angle connector from 80/20. This is product number 14057. ... Used with 20 series extrusions

I use this to keep my wires inside the grooves of the 80 20 extrusion.

Feet for Ender 3 Pro, but should fit any 80/20 extrusion.

This i a bottle holder that i made for a sim racing rig. Mount is flat backed so you could really mount it to anything. designed to use a M6 bolt or screw. No support or rafts required. ...

Aluminum extrusions from 80/20 inc. Model 2020, measure 20mm by 20mm. ... Extrude to your needed length.

A foot I designed for some shelving out of 80/20 extrusion I designed. ...it's faIrly rugged and can be made without supports.

Corner bracket for connecting 80/20 10 series extrusion. Depending on your printer, the fit is pretty tight. ... You may not even need to screw it in.

80/20's 40 mm aluminum framing extrusion. ...40mm X 40mm Ultra-Lite T-Slotted Profile - Four Open T-Slots Part Number: 40-4040-UL

80/20's dual 40 mm aluminum framing extrusion. ...40mm X 80mm Ultra-Lite T-Slotted Profile - Six Open T-Slots Part Number: 40-4080-UL

Small connector that link 80/20 shafts together. ...It can also be operate in vertical movement with the connector holding both the shafts.

This is a T-nut designed in Blender for use in 1.5" 80/20 rail. ... Updated 7-6-18: included pre-tapped versions M8-1.25 and 1/4-20

Lighting: Good 80-20: Good Cheap Chinese COB arrays: Good This thing: Triple Good These snap on and screw on to 80-20 extrusion, and hold COB LED strips from Banggood. ...Great for easily adding lights to a thing, or making an industrial lamp.

80/20 Aluminum extrusion used to make "erector set" assemblies, fixtures, workstations, etc. Other versions are available online but needs to close the loop on all entities before extrusion is possible. ...Drawing 80/20 parts is time consuming, so I...

80/20 Aluminum extrusion used to make "erector set" assemblies, fixtures, workstations, etc. Other versions are available online but needs to close the loop on all entities before extrusion is possible. ...Drawing 80/20 parts is time consuming, so I...

... it worked well. The bolts I used were from 80/20 - they are the bolts from the 10 series standard end fastener. The nut is the economy T-Nut. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6vT7ET4nLfA

These are 80/20 linear bearing plates that I designed and used for my First Tech Challenge (FTC) robotics team. One file has the slider plate without the bearing pad, as you can purchase the bearing pads yourself on Amazon and they work much better...

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: interiorFillet = 5 sidewallWidth = 1.1 hingeLengthScale = 1.1 hingeThickness = 0.3 interiorLength = 65 tabSize = 1 interiorHeight = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: hingeFillet = 3 interiorHeight = 20 rimInset = 0.6 sidewallWidth = 1.1 interiorWidth = 80 interiorFillet = 1 hingeLengthScale = 1.1...