92 mm fan 3d models

Support and anti vortex for 92 mm fan.

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: bracket_height = 38 cross_bracket = 10 bracket_thickness = 4 fan_hole_spacing = 82.55 pcb_width = 60.0 screw_diameter = 5 bracket_length = 12...

a 92mm fan mesh for filtering big stuff

A remix of the fan cover for a 92 mm fan :)

Just a remix of Niak_Nia's PSU Box with a 92 mm Fan. You have to measure the voltage before to know, if you need a buck converter or not. ... And please don't work on the PSU under current and only when you know what you are doing!

A 92 mm mesh for a fan to put some filters inside of

Customized version of https://www.thingiverse.com/thing:3320712 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3320712

It is designed for 92 mm fans. The overall thickness is 4 mm, but the honeycomb is just 2 mm thick, allowing a gap to the blades of at least 2 mm. It is not a strong guard, but should work just fine for avoiding fingers and wires from getting caught...

It is designed for 92 mm fans. The overall thickness is 4 mm, but the honeycomb is just 2 mm thick, allowing a gap to the blades of at least 2 mm. It is not a strong guard, but should work just fine for avoiding fingers and wires from getting caught...

Solder fume extractor for 92 mm fan and a LED strip. To fix the fan on the extractor you need 4x M4x10 screws. The diffusor has to be printed in translucent filament. ... Print orientation is shown above in the STL previews.

Issue is the fans were not providing sufficient air and were hella noisey so i designed this case to use a 92 mm fan to provide tons of cooling all while being silent. ...If you take a look at the images youll see all the parts i used to make this...

Remix on “Anycubic Kobra - Power supply cover for 80mm fan” by lucky449 One day I started to hear a lot of noise from my 3d printer, so I decided to replace a fan at the bottom, I choose 92 mm fan as the biggest that fits and simply because it is...

Remix on “Anycubic Kobra - Mainboard cover for 80mm fan” by lucky449 One day I started to hear a lot of noise from my 3d printer, so I decided to replace a fan at the bottom, I choose 92 mm fan as the biggest that fits and simply because it is...

The place for the 92 mm fan is designed with some tolerance and should need fastening, I therefore added screw holes so that you could fasten a bracket behind the fan (or rather in front if you plan on using it as intake as I am). However, I found...

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: bracket_height = 36 cross_bracket = 10 bracket_thickness = 3.0 fan_hole_spacing = 82.55 screw_diameter = 3.25 pcb_width = 60.0 fan_size = 92...

It is made to hold a Noctua NF-A9X14 PWM, but another fan with the same size (92 mm), hole spacing (82.5 mm) and a maximum height of 14 mm might work as well. The fan mount is attached to the two holes in the printer case that hold the original...

A remix of https://www.thingiverse.com/thing:4202455 Changes from original: - thicker walls - sturdier screw holders - tilted ventilation holes Tested with Sunon HA92251V4-1000U-A99 silent fan.

With this one you can use a 92mm fan together with a LM2596 DC-DC stepdown converter, the internal fan connector of the PSU has a voltage of 24 V common fans run with 12 V. With this cover you can lower the noise of your Ender-3 PSU. Keep in...

You'll need a metal fan cover (around 3 EUR...) to screw onto the fan as well. The LM2596 sits inside in the PSU. Use the screws that are normally provided with the fan for attaching it to the cover. You may need to turn the model around in your...

*Whole distance and overall size is correct *other parts were measured or made by eye assumption

Duct designed to adapt a 92 mm fan into a dust blower. The design reduces the output dimensions significantly, theoretically leading to faster air speed and focused air flow. It requires a powerful fan with high static pressure, such as the Vantec...

Duct designed to adapt a 92 mm fan into a dust blower. The design reduces the output dimensions significantly, theoretically leading to faster air speed and focused air flow. It requires a powerful fan with high static pressure, such as the Vantec...

... cable management case. ...A 92 mm fan is required. Feel free to improve :) PS: You will have to flip the Motor on the x-axis. ...Because of that you will also have to flip the x-carrier or adjust the direction of the x-movement in your firmware.

Ikea-Lack housing fan duct for a 92 mm fan with static pressure enhancer (axial compressor). Helps to extract odors from the enclosure and remove them using an optional 50mm suction hose.  Update 05.04.2022:In order to increase fan...

Ikea-Lack housing fan duct for a 92 mm fan with static pressure enhancer (axial compressor). Helps to extract odors from the enclosure and remove them using an optional 50mm suction hose.  Update 05.04.2022:In order to increase fan...

Also the mounting holes for the 92 mm Fan are meant for threaded inserts. You can find some Info about threaded inserts on the YouTube channel of CNC-Kitchen. PSU-COVER WITHOUT THREADED INSERTS: This cover has smaller screw holes so you can screw...

I printed this a few years ago and can't remember the settings I used, but it does not need support in the right direction. ...I've used this as a way to vent the steam away during beer brewing.

I made this fan guard for the Noctua NF-A9 FLX which I mounted on the cover of my Geeetech A10 power supply. The guard is supposed to be mounted only on the side of the fan, where the air comes out. This is because of the hole in the middle I left...

Easy to print 92 mm fan grill. Honeycomb infill is big allowing free flow of air. ... If you want other sizes, let me know.

... is from an artic am2 cooler. ... I printed with 0.2 layer height. The part with the fan is 2 mm thick, the notch 2.4 mm, in my case it fits perfect, but if you print with lower than 0.2 maybe it will wobble? ... I used the original rubber fan mounds.