986 porsche 3d models
4873 3d models found related to 986 porsche.thingiverse
Ball mount for phone holder for Porsche 986 stock stereo. I modified it from: https://www.thingiverse.com/thing:4706682 in TinkerCAD the ball appears to be about 17MM. Worked perfect with a phone holder I already had. ... I printed it and put...
cults3d
Designed to fit the Tamiya 1/24 Porsche 986 Boxster. ... The insert resembles the trunk reinforcement of the real car.
cults3d
Designed to fit the Tamiya Porsche 986 Boxster. Theoretically, it should fit the Porsche 996 from Tamiya too, but this is still untested. The insert resembles the hood reinforcement of the real car. 2022-06-08: Altered the design to aprox 30%...
thingiverse
This is a simple tool for inserting RMS (Rear main seal) on Porsche 996 and 986 engines. When the tool is bottomed against the flywheel flange, the seal is seated 13mm below crank flange. Use flywheel bolts to push tool and seal. ... Note the...
thingiverse
A simple holder that fits perfectly in the Porsche Boxster S 986. Tried it in my 2001, so should fit all in the same range. You could lower the bars holdin the can in place, but i'd rather have them higher to prevent them from being shaken to...
prusaprinters
I went ahead and created new fonts and numbers for our Porsche 986 as the old one were long gone. This has been our fixer upper car and it was great to print a part that are as expensive as 80 euros. </p><p>The print is pretty simple and is as...
thingiverse
Removable cupholders for Porsche 986 Boxster. Bracket wedges in between Center dash and Upper Center Console as shown. Cupholders can be stored in armrest when not in use. Assembly Instructions: 1. Insert the shorter side of bottom supports...
thingiverse
This is a cam holding tool for the Porsche 986/996 Boxster or 911 early 5-chain engines.
thingiverse
This part is used on (at least) the 996 (911) and 986 (Boxster) to secure a plastic cover between the headlights in the front trunk (frunk). You'll need 4 of these to secure the plate. The original ones had broken "legs" or humps at the bottom, so...
thingiverse
This phone holder is meant to fit inside the empty storage slot underneath the radio. This phone holder was designed to fit the phone holder below, which can be purchased from Amazon. ... Link:...
thingiverse
This attaches to the clutch master shaft to reduce clutch pedal travel for use with clutch disks which need over-travel protection (e.g. ...a Tilton OT-2 7.25" twin disk)
thingiverse
A 986 has over a dozen of these nuts, they're also used to secure the carpet on the engine cover behind the seats. The original ones tend to get loose or break over the years, so I needed a few new ones. I designed these using a 10mm nut and...
3docean
The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi...
thingiverse
Add a cup holder to a Porsche 996 or 986 that has the ashtray delete part installed. Pull up the rubber liner and remove the two screws. Place the bottom piece in position - it only fits one way. Replace the screws. Insert the top piece. Done. ...As a...
thingiverse
modification du CDTRay de la Boxster 986 2002. démontage avec précaution du CDTRAY pour conserver le cadre. Impression des 2 modules Pour le Module de support il faut enlever les support pour dégager la gorge ou les clips se positionneront Vis M3...
thingiverse
Remix of trevorbattle's Cup Holder design. This has a base for the print so you can place things inside (besides drinks) and not remove it to grab something. Fits nicely in my car. Despite being PLA (in my case) it has yet to melt in the Florida...
grabcad
Measured from actual part.Mounting dimension tolerance +/- 0.25External dimension tolerance +/- 1.2500 Boxster S Porsche 986 L R REAR Red BRAKE CALIPERS # 996352421 996352422 86,562
cgtrader
The 3D model was created on real car base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.
cgtrader
The 3D model was created on real car base. Itâs created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format)...
cgstudio
The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...
thingiverse
Remixed to fit American size drinks. Can fit a small camelbak water bottle or 32oz soda cup. ... Print upside down with supports.
thingiverse
If you're keeping the tweeters or upgrading, these clips can be brittle now the plastic is around 20 years old. ... A little different (flat backed) for easier printing but matches really well.
thingiverse
This is a Phone Mount for my Porsche Boxster 986 S Spyder from 2004. The ball joint allows you to change the viewing angle of the Tablet/Phone you want to use. I Custom made the mount to perfectly fit on the upper right part of the storage...
thingiverse
Printed in ABS, requires a the type of phone holder with a magnet on the phone and a sphere glued to the holder. ...The printed holder needs to be attached with screws or tape so that when you take the phone off, the whole thing does not come out, there...
thingiverse
This bracket presses into the locked storage container and makes it into a double cup holder. In my case I'm using it to replace the wonky in-dash cup holders so I can use that space for a double-din stereo upgrade. The lid can still close and...
thingiverse
This is a very basic substitute for Porsche special tool for installing the rear main seal. It should work for Boxster 2.7 engine up to 2004 with a 'new style' PTFE oil seal that needs to be installed at 13 mm depth. Check your service manual to...
grabcad
fuel cap hinge missing? ...print itABS tested for 3 months, no crack