996 rear wiper delete 3d models
50778 3d models found related to 996 rear wiper delete.thingiverse
Simpel plug to cover the hole when deleting the rear wiper of a Porsche 996. Fixates using bathroom silicone or glueing a M4 bolt to the bottom. ...Super light weight!
thingiverse
I designed a wiper delete Bung for my EP3 Civic Type R Same as the one found on ebay ( see photos ) Change filament at layer height for a better look! I made an embossed one and debossed version Attaches with silicone Any questions feel...
thingiverse
Rear wiper delete bung for an Audi a3 8P infil 10% Ender 3 pro no need for supports no clean up secured to car with silicone PLA Short print time
thingiverse
Rear wiper delete for Mini R53. Hello fellows, the rear wiper broke on my Mini R53 and I just got rid of the thing, less weight is better right? This part plugs the hole in the rear window when the motor is removed. ... To complete the assembly you...
thingiverse
This cap is used to delete the rear windshield wiper on 2007-2011 BMW 3-Series wagons. The wiper shaft is removed but the handle and glass-opening button remain for convenience. The cap model has build-in support that can be broken away with...
prusaprinters
I have designed this because I needed a plug since my wiper was defective and replacement motor was late :) If you like it without the wiper than this one is perfect fit. If you want you can use a screw and a washer from inside to prevent any...
cults3d
This cap is used to delete the rear windshield wiper on 2007-2011 BMW 3-Series and 2004-2010 5-series wagons. The wiper shaft is removed but the handle and glass-opening button remain for convenience. The cap model has built-in support that can be...
thingiverse
This is designed for porsche 911 996 models, used for radio delete box, drawer call it whatever you want. A closure for back porsion is leaved oped to do a different project. Anything can be used for back cover. ...Fits loose, need some tightening...
thingiverse
I designed this Wiper Delete plug for a 2008 Skoda Octavia because the rear wiper stoped working and the owner didnt want it anymore. ...Straight off plug, just get some quality glue and glue it in the hole
thingiverse
... ...When the motor is removed the plug is left open. This seats up against the factory seal and locks in place to mitigate corrosion for those who have deleted their rear wiper. May fit other applications as well. ...This fits the plug on my mk7 gti.
grabcad
996 Rear Spoiler Assembly, Modeled & Rendered in Fusion 360
thingiverse
... 106 superturboawesomeskiponwheels. ... I expect it's probably a pretty generic part for cars with rear wipers around that age. ...(should definitely also fit Citroen Saxo too) If you make it and it fits yours, stick in a comment to let others know.
grabcad
This gear is part of rear wiper mechanism mounted on 2012 NISSAN Juke car.The teeth of the original one were completely broken due to premature wear, thus the sweeping motion was not smooth.I redesigned a new gear by measuring the old one and 3D...
thingiverse
Rear wiper cap to replace the OEM broken cap on a 9n3 Polo. Works in 2 pieces which clip together. Simply print the base and any top part of your choice. Should also work with other listed VW model: - GOLF mk5 - PASSAT B6 - POLO mk4 -...
thingiverse
I have designed this because I needed a plug since my wiper was defective and replacement motor was late (COVID) :) If you like it without the wiper than this one is perfect fit. ...If you want you can use a screw and a washer from inside to prevent any...
thingiverse
Add a cup holder to a Porsche 996 or 986 that has the ashtray delete part installed. Pull up the rubber liner and remove the two screws. Place the bottom piece in position - it only fits one way. Replace the screws. Insert the top piece. Done. ...As a...
thingiverse
2009-2016 Honda Pilot Cover on the rear window wiper came off, so modeled this one. ... Attach with hot glue.
cults3d
I had my rear wiper seal ripped off on my pt cruiser so I made a replacement seal in TPU, because I couldn't find it.
thingiverse
This cap is a replacement part for the Fiat Coupe rear wiper cap. I have printed it, only with outlines (i think 3 to 4) with a resolution of 0,2mm. Therefore i used support in the inside. ...
cults3d
Here is a creation for our Laotie T30 in 10 inches, a rear wheel wiper to avoid water or mud projections. The dimensions are 150x100x66mm and a thickness of 5mm on the whole piece. ... You just need to make a flat iron bracket, hooked to the swingarm...
cults3d
Following a specific request, to replace a rear window wiper cover on a Peugeot 107. 3D construction, then printing on Anet A8 in Black Polymax. After deformation under the heat of the sun, made of PET "Cunning Clear" (ICE). Then more technical...
thingiverse
Cap on nut of rear wiper Ford Fusion. I lost, it seems (over time, the plastic harden and bursts) Cant found in sale, so had to draw it. Printed 0.3 mm layer, 100% infill. No support needed. Put tightly. There's also a SketchUp model file...
thingiverse
This is a plastic cap that covers the (recessed)13mm nut that attaches the rear wiper arm for late model Dodge Caravans and Chrysler Town&Country minivans After exhausting my search on the internet for a 3D printable design, I designed one myself. ... ...
cults3d
Here is a creation for our Laotie Ti30 in 11 inch, a rear wheel wiper to avoid water or mud splashes. The dimensions are 153x120x64mm and 5mm thick all over. ... You will just have to make a flat iron bracket to hang on the swingarm or the wheel axle...