9mm magazine loader 3d models
24540 3d models found related to 9mm magazine loader.thingiverse
Magazine loader for the sten gun 32 round 9mm mags Instructions Print 100% fill with supports this is a easy clean print.
thingiverse
I fine tuned the sizing to exactly fit the SpringField XD 9mm magazine. The original was too loose and sloppy for my taste. This one is more solid and fits snug, yet slides nice and smooth. Printed using PLA+ Object printed upside down , NO...
thingiverse
Fits Smith and Wesson M&P 9mm double stack magazines. Printed at 0.3mm layer height, 1.2mm walls, and 40% infill Orient upside-down and you shouldn't need any supports. ...
thingiverse
Exact copy of pgm250's magazine loader, but with built in supports, allowing you to print it vertically so you dont need to use slicer generated supports, or put supports on the inside of it, which can be hard too remove. Rotate so its printing...
thingiverse
This is a remix from https://www.thingiverse.com/thing:4720873 I like my loaders to have names on them to be more easily identifiable.
thingiverse
This is my take on the 9mm Magazine Speed-Loader for the Springfield Armory Hellcat Magazine. The push stim is wider and at 20 degrees to match how the rounds go in. ...this helps a lot on loading to help loading.
prusaprinters
This is my take on the 9mm Magazine Speed-Loader for the Springfield Armory Hellcat Magazine. The push stim is wider and at 20 degrees to match how the rounds go in. this helps a lot on loading to help loading.</p> <h3> Print Settings</h3>...
thingiverse
I threw this together real quick when I found there wasn't a magazine loader for a 9mm 1911. This works on my Mec-Gar magazines, but assume it'll work just fine on others for the 1911. It works just fine, but I think I'll end up getting an Uplula...
thingiverse
OPERATION: The speed loader is placed on top of the magazine, and pressed downwards (see figures). A small boss depresses the top round in the magazine and in turn compresses the magazine spring. Another round is then loaded, from the front, and...
thingiverse
Speed loader I designed for a 9mm Glock magazine Printed upside-down for pusher strength.
thingiverse
Speedloader for 9mm UZI magazines. ...SLDPRT, STEP, and STL files included.
thingiverse
Just resized the width so that it will load a single stack a little easier. ...I measured this to fit my PF-9 magazine. ...Inner diameter is about 13mm.
thingiverse
Additionally, I've added an access hole at the back of the mag loader to allow a stuck round to be pushed out and ejected (should be a rare case with this modified version) This thing was remixed with Tinkercad. ...Edit it online...
thingiverse
Printed this upside down with towers so that the pusher piece would be stronger. ...50% infill
thingiverse
Print upside down with minor support. I printed in 69% gyroid infill, 4 walls, .12 layers but you can do pretty much whatever just make sure the 'round pusher' is strong. ... Tested with standard 10rd mags and the redball 20rd mags Included...
thingiverse
Was not thrilled with the few models I found here and elsewhere, so I designed my own. I printed this on its back with supports (inside and under the tab). ... Enjoy.
thingiverse
Created just to see if I could. One of my first design projects, feel pretty good about the outcome except for the ridges at each of the bottom corners. If you don't like it, you can remake it to your liking. I couldn't (and still can't) figure...
thingiverse
Created just to see if I could. One of my first design projects, feel pretty good about the outcome except for the ridges at each of the bottom corners. If you don't like it, you can remake it to your liking. I couldn't (and still can't) figure out...
thingiverse
... 2 (bottom up) due to strength and no support at the part hitting the bullets. ... Tip: if you printer have som shrinkage of the material, please scale up to 101% Fits my magazines on a S&W M&P M2.0, But should fit most similar full size mags. ...
thingiverse
Simple speed loader or thumb saver for CZ 75 magazines. Tested on stock and MEC-GAR mags. Recommended use shown in pictures. Based on HAL_9000_HAL_9000's Ruger design. Check him out. ... Printing: In orientation shown in 3D render (on its back) ...
thingiverse
This is redesigned for use with a .380 or 9mm single stack magazine. Originally tested with a smith and wesson .380 single stack pistol. No need for support. ...Print in the position it loads in.
thingiverse
print with the top down infill at least 40% probably competible with most of the magazine out there. ...Print Settings Printer: flashforge ...
thingiverse
This is designed to aid the process of loading cz 9mm double stack magazines but you could download and alter dimensions to work with most any magazine. I printed with PLA. I set my perimeters/top/bottom to 7 layers w/ 100% infill with supports as...
thingiverse
This is speed loader for BLANK bullets in pistol. ...Pistol is copy of Beretta M92.
cults3d
The DU4 magazine is a universal, pocket-sized pistol magazine designed to load virtually all 9mm through .45ACP single and double-stack Luger magazines from all manufacturers. It also loads most .380ACP single and double stack magazines, and 1911...
thingiverse
This is a remix of my other loader - this one sized for the Smith & Wesson M&P Shield. ...Should work for both the 9mm and ,40 S&W version of the magazines.
thingiverse
May work for other staggered 9mm magazines. Please post a comment if you find out this works for another pistol. I have optimized this file for printing upside down without supports. Ergonomic features added, internal alignment feature added,...