bmw r1200gs 3d models

Tele Lever cup for the BMW R1200GS models

frame plugs for the bmw R1200Gs LC ( K50) You wil need some O-rings to complete the set enjoy

BMW R1200GS Headlight protection. Need to change original bolts with some longer. ...Installed on the original holes, no other frames required.

Tool Box door for BMW R1200GS moto.

Seitenständerverbreiterung für BMW R1200GS Rally BJ.2013

This is an under-seat storage solution for the BMW R1200GS to store more tools and misc items, or in my case to store a wera toolset in addition to misc items. This is a work in progress I am still trying to get the dimensions right and also the...

Imbuto per olio motore BMW R1200

I made a model of the known BMW GS Commercial. You can customize it, make a Keychain , 3D Sticker or Badge.This is why i didn't put a hole for the keyringIf you need the Stepfile just let me know. 

Thi is a support for mountig Garmin Zumo adapter on 12mm tube of BMW R1200GS

Used to remove Spark plug coil from my Bmw R1200GS LC 2013, if you have lower crash bars, they may be in the way!!! ...

Handlebar bar mount for BMW R1200GS Slightly heat the plastic to deform it slightly when it is mounted on the handlebars. Concerning the handlebar bar, it can be made out of a 20mm diameter aluminium tube, folded and cut at the ends. ... Tube length =...

Additional LED mounting for BMW R1200GS or any other motorcycle using crash bars or 25mm tubes. ... LED model l4x = ...

Simple low-profile one-piece wall mount for Lego Technic BMW R1200GS Motorbike kit. Needs two short Lego Technic Axles and one Lego Technic Pin (3673), which fix the model to the mount in three locations. No mods required to the model itself. ...

Broke the right handguard bracket of my 2007 BMW R1200GS Didn't want to pay more shipping than the piece costs, so designed one myself. I've printed it horizontally where the single hole is situated. This gives the strongest layers for the design....

This is an easily printable oil filter wrench for **BMW R1200GS LC** for original BMW and aftermarket HI-Q (outer diameter 76 mm) oil filters. It is __not__ necessary to use supports. **Note!** You need a 34 mm nut to use this. Version 2 has a...

I printed and installed this GoPro mount for the windscreen of my BMW R1200GS. https://www.thingiverse.com/thing:1904555 This design mounts a GoPro Bluetooth Remote to the 28.5mm diameter handlebar on the bike using the standard adapter clip that...

This is a bigger headlight dust cap for a BMW R1200GS 2004 model (confirmed but it should fit newer models as well) for LED conversion. Due to a heatsink or a mini-fan usually found on these types of bulbs, the original cap (part number...

I required a tool to help flush the brake-fluid in my 2005 BMW R1200GS, without introducing air into the servo-assisted circuits. And I did not want to spend lots of money and time waiting for it to arrive. As far as I know, this funnel should fit...

BMW R1200GS Logo - I printed it in 2 Colors White/Blue No Rafts / Supports

Hallo. ...Hier Kofferhlater für die BMW Variokoffer der LC für die Wand montage.

To replace the original part number 63 12 7 653 586. ...The original part often breaks down because of bad roads.

support for switch info or ....

Si consiglia di stampare in modalità "fine" per un risultato piacevole alla vista. ... Usare i supporti per la stampa.

The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi...

Handle Fog Light Switch Control for BMW R1200GS

My left handguard mount for my oil-cooled R1200GS broke. I designed a replacement for it. The part is for the left handguard. ... I'm sure that it's reversible for the right handguard.

Confirmed to work on my 2010 R1200GS coils. I recently trimmed back the inner portion of the puller as it was a tight fit on my bike. Please let me know if its too loose and I will post my original model. The coil/cap for my bike measured 26.8...

I created a holder to fit my tomtom rider 450 to the 12mm tube where the genue BMW Navigator was mounted. ... Infill 50% PETG CF 0,1mm Don't tighten the screws (2x M5x25mm with 2 washers) to much!

On my BMW r1200gs lc k50 had Need Full Bunker Exclusive crash bars were installed. After that, the mounting block of the original fog lamps could no longer be installed, its place was taken by the mounting of the upper arches. Hinged mounts of...

Customized version of http://www.thingiverse.com/thing:74322 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=74322