ALFA Network AWUS03H Tripod Mount Clip 3d models

Tripod mount for Amazon Basic tripod. ... Just on the fly.

I didnt have a replacement clip for my AWUS036ACH and couldn't source a part locally, so I designed and printed one. ...Maybe this might find use to someone in a similar boat. Reference part /part replaced in this design is the far left of below:

it's two parts the holder and the clamp the holder can be print with support internally on the flat surface with 40% infill the clamp base need to be 100% infill print also on the flat surface without support the top clamp will need support under the...

... Dimensions outside (WxDxH) 1.5cm x 1.5cm x 0.4cm Dimensions inside (for the cable): 6.3mm x 1.5mm english: A simple cable clip for flat network cables. Can be fixed on doorframe or baseboard. Stick it with some glue, 3M tape or something like that.

Mounting a cylindrical item like a flashlight or laser pointer becomes easy with this accessory, as it works seamlessly with standard tripods.

Tripod camera mounts for sale.\n\n \n \n Quick Assembly Guide\nUse a 3D printer to create one and secure it using UNC 1/4 or WS 1/4 screws today!

Camera mount for Bosch tripod. I designed in Fusion360 and printed in carbon fiber PETG. I needed additional mounts for a ham radio satellite antenna and some other projects and couldn't find exact parts info online. I use a 1" 1/4-20 carriage bolt...

this is a bracket for a tripod with quick release.

So i found a broken no name tripod and i wanted to fix it that is why i designed these replacement parts if u think that may work for you feel free to print them

Any slender box can easily attach to a standard photography tripod using a 1/4-20 UNC screw. ...This attachment requires a high-quality print, preferably one with excellent resolution and clarity.

I could not find any 1/4-20 threaded microphone holders, so I made my own! It uses a heat-set insert like the one shown below. I hope you like it! ... https://www.mcmaster.com/94459A380/

this is a bracket for a tripod with quick release. Print Settings Printer: Crealety Ender 3 V2 Rafts: No Supports: No Infill: 15 Filament: 3D Jack ECO Pla PLA Black Category: Camera

Attempt to make a GoPro mount that works for both a quickrelease tripod (AmazonBasics tripod) and a GoPro buckle sticky clip bought from eBay. The fit my tripod is perfect, however the buckle clip is a bit looser then I'd like for actual use.

Mounting an Arduino network module inside a protective casing is essential for safeguarding against accidental damage and environmental factors.

I aimed to replicate it as accurately as possible, incorporating additional features such as frame mounting and provisions for a Warn-licensed 1:10 scale winch. The RC4WD cable rollers are seamlessly integrated into the design. Tight tolerances are...

Originally created to attach an old Dell 2724 to the wall of a networking closet, this design should work for a wide range of networking appliances. The mount is intended for devices that are approximately 45mm thick or 1U in size. One corner...

https://www.printables.com/prints/97432-netgear-gs305-switch-under-desk-mountI just lazily clipped out 5mm worth of depth out of the base plate and shortened the clips slightly. Print this as it imports into the slicer. Laying it down leaves the...

I reconfigured the Roku Ultra wall mount to fit a Dish Network Joey, adapting it to accommodate the slightly irregular screw holes. To access the front buttons on the Joey, I discovered that part of the mount needed to be carefully cut away. Once...

Humans use a clip to secure Celestron tripod legs together in multiple configurations.

A simple "springy" phone mount for a 1/4 20UNC equipped camera mount or tripod. The thread is already there. I set it to clamp a Samsung S6 Edge, but I suppose any phone will fit, when you set the dimension right. Apparently it was easier to...

This is a design for replacement of a nedo tripod clamp clip. ...Printed in black PLA with all supports and 50% infill.Tripod is often used for levellers / theodolites.

My Cat5E cable has a diameter of 5.5mm, which is likely similar for other brands, so if yours is close, this mount will work just fine. I've updated the design to accommodate cables with diameters less than 8mm. When attaching the cable, be sure...

This is a wall mount housing for a RJ45 coupler. 26mm diameter. ... Coupler inlays: https://www.amazon.de/gp/product/B07Q345W78?ie=UTF8&psc=1&linkCode=sl1&tag=croonentech-21&linkId=c2d09fdd50c3cb8ae5b60d787caf15a0&language=de_DE&ref_=as_li_ss_tl ...

This is a wall mount housing for a RJ45 coupler.26mm outer diameter.It is designed for these coupler...

I designed this iPhone bracket to hold my phone securely in its case while allowing it to be mounted on various tripod brackets. The 68mm clip opening provides a snug fit, and the loops for rubber bands apply gentle pressure to keep the phone firmly...

so i made a tray that works with @russross raspberry pi 4 1u rack-mount bracket project. ... https://www.thingiverse.com/thing:4125055 this macmini tray module is designed to replace 3 of the 6 pi modules that would make up 1u on the rack. ...

this is a clip that is made for the rollie smartphone tripod traveler to hang it on your wall. ... ti is printit in pla

... of the clips to adjust the height was broken. I asked him to take the measurements and by trying to get an unbroken clip - he broke another one. So I printed a bunch of those. They did fit and money for new tripod saved. ...Designed in FreeCad.</p>

Printed in black PLA with all supports and 50% infill.Tripod is often used for levellers / theodolites. Print instructionsCategory: Tools This is a design for replacement of a nedo tripod clamp clip. Printed in black PLA with all supports and 50%...

This phone clip for a tripod boasts a 41-mm quick-release shoe that can be inserted directly into a tripod. It also stands confidently on its own on any flat surface. If your tripod features a different quick-release shoe size, you can easily edit...