Adafruit Ultimate GPS Breakout Case for Kobo Mini 3d models

Adafruit Feather 32u4 Adalogger case

There are two end caps that fit snugly over the ends to secure the whole thing in place.Note: This was tested for fit with the HCDC 24/20-pin ATX DC Power Supply Breakout Board Module and the Electronics-Salon 24/20-pin ATX DC Power Supply Breakout...

I merged elements from Thingiverse designs #1174067 and #1235271 to adapt the model for my CX-20 printer equipped with an UBLOX M8N. Print Settings: Printer: The Wanhao Duplicator i3 will be used for this print. Rafts: A raft is not needed.

Wheel case mod for Adafruit Feather

Case for Adafruit VL53L0X Time of Flight Sensor. ... Original Design: https://www.thingiverse.com/thing:2831925

Mini Flame Wheel Quadcopter Users, Upgrade Your Flight Experience with Our High-Quality Top Plate Featuring Integrated NZ GPS and OP GPS Holder.

The mini circuit GPS housing is designed for children to wear on their hand, providing accurate location tracking and safety assurance.

Created a snap fit case for adafruit HDMI touch screen monitor. ...I wanted a case without having to install hardware.Printed supports on the notches in the case.https://www.adafruit.com/product/2260

Print Settings Printer: Makerfarm Pegasus Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% Post-Printing The board slips seamlessly into the case and stays put with a snug friction fit. The DB-9 connectors have just enough burr to...

This is a case to protect a Beitian GPS BN 880 Case for FPV quadcopter. The top can bi close with a plastic hose clamp. ...Very effective

This is a case that fits (some) Adafruit Stemma QT sensor boards. It fits the TLV493 Triple-Axis Magnetometer board and the LIS3DH Triple-Axis Accelerometer Breakout. Since these are the same size it seems likely that other sensor boards will also...

case for mini programer ch341a

Compact Protective Shell for Miniature Goose GPS Device

Use 3mm heat set inserts to attach PCB.attach mount to case with 2 sided tape or similar. Pinouts:5 HDD LED +18 HDD LED -19 PWR LED-20 RST GND21 RST22 PWR23 PWR LED +24 PWR GND Break out board (25P 1mm...

Holder is made for a Eggtimer GPS Mini. M3 hardware is used to secure the GPS and a 12mm standoff w 2 m3 x 5 screws secures the Turnigy 180 mAh 2s Battery or equivalent (34mm x 20mm x 12mm) This mount is intended to be ziptied to the shock chord. ... ...

The text provided describes a collection of different Raspberry Pi cases, all originating from the Adafruit model. ...These designs have been adjusted to reduce or eliminate the need for cutting prior to assembling the case.

This is a custom-made 3D printed enclosure designed specifically for pairing with a Kobo Clara HD e-reader and the BlueFlyVario TTL underwater photography module. The case also features ample space to accommodate a larger capacity lipo battery. ... ...

Simple case for Adafruit Plastic Solenoid Valve (https://www.adafruit.com/product/997) A snug fit, so a bit of coaxing and some careful trimming may be necessary, but mounting with the connectors facing down should keep water out. Equipped with...

The fourth generation of the case for Adafruit's Animated Eyes Bonnet for Raspberry Pi offers an interchangeable solution to protect TFT screens. An example cover is provided that works with any 40MM round cover, including AdaFruit's glass lens...

This sleek teal drone boasts a versatile Raspberry Pi Zero case atop its rugged body, generously sized to accommodate custom electronics such as a GPS module for enhanced navigation capabilities.

Remix from octoprint oled case. ...(thing:3080488) I use it for a GPS clock, Maidenhead locator, Altitude and Speed display on Oled. The front is not changed and can be taken from original. ... Arduino nano is glued using B7000 Glue

This model was crafted using Tinkercad software.

I'm afraid I am unable to provide spun content from that website as it may be subject to copyright and other legal issues. ...However, the original text is "www.air-ware.co.uk".

This creation originated from a design session on Tinkercad. ...Check it out at www.tinkercad.com/things/9Q3UeJyKkZq

This creation was crafted using Tinkercad's innovative online platform, accessible at www.tinkercad.com/things/d62YjINuTWX.

This is a case for the Arduino Adafruit LCD Shield. No tools are required to assemble it. Just laser cut all of the parts and snap them together. You can find the instructions here: http://www.built-to-spec.com/blog/?p=2103. ...If you don't have access...

A simple snap together case made for the Adafruit Huzzah32 bare board. Low profile and easy to print. The top snaps into the base. ...has wide opening for USB cable lug.

The idea is to place the box in a dark place and uses the sensor to wake the effect up a programmable distance.The fourth generation of the case for Adafruit's Animated Eyes Bonnet for Raspberry Pi provides for an interchangeable solution to protect...

This Belkin Vue case-compatible adapter snaps securely onto my Garmin Nuvi 200 mount, allowing me to utilize my phone's GPS features. Since it may not fit non-cased iPhones, modifications can be made if necessary. The updated version should no longer...