Auto level sensor bracket for Prusa i3 R2 3d models

Here is another Prusa MK3 PSU-Bracket / Brace. Please take a look here https://www.thingiverse.com/thing:3898665. It fits between Mainframe and Rearplate, clicks into place top and sidewise in the 3030 Extrusion to make it more rigid. You can...

This mountig brackets are for the bigtreetech TFT50 Display on a original Prusa i3 MK3s. You need a allen key with rounded head to be able to tighten the screws. The bores for the display are designed with a 2.8mm diameter. It should be a bit...

I constructed an enclosure for my Prusa I3 V 2.5 by hand. As many have discovered, this necessitates readjusting the cable that connects to the print bed so it attaches at a precise 90-degree angle. Various designs on Thingiverse can accomplish this...

This is another Prusa i3 LCD holder. The LCD display (from RepRap Discount) is installed horizontally, leaving free the top of the printer. It can be installed either on the left or the right. One of the LCD holders has a slot for the SD-card.You...

I cracked a fragile part of the plexiglass enclosure around my Prusa i3 by over tightening a screw. I designed an exact replica to take its place and even upgraded both to utilize it as a single piece - it functioned incredibly well. I'm sharing my...

This is another Prusa i3 LCD holder. The LCD display (from RepRap Discount) is installed horizontally, leaving free the top of the printer. It can be installed either on the left or the right. One of the LCD holders has a slot for the SD-card.You...

... on my setup. To use a standard 3mm Allen screw and nut, I modified the design slightly, making the mount longer to accommodate my shallower frame mounting. Print Settings: Printer: Prusa i3 Rafts: No Supports: No Resolution: 0.2mm Infill: 50%

This part is an enhanced cable chain designed specifically for Geeetech Prusa I3 Aluminium 3D printers. No additional screws are required - simply print and mount using the existing screws. I drew inspiration from...

http://www.thingiverse.com/apps/customizer/run?thing_id=166045 Instructions Using the following options: Cross-bracket spacing set at 10 PCB width measured precisely at 49 units Screw diameter fixed at 3.25 millimeters Bracket length customized to 12...

I isolated the original STL from Jason3030 into separate LEFT and RIGHT models. ...On my Prusa MK2S, I had to employ supports specifically for the left side.

The sensor diameter used for this bracket is 8mm, but you can easily adjust it to fit your sensor type by editing in your preferred 3D editing software. Note: I printed the bracket at medium resolution as shown in the pictures. PLA was my material...

I wanted to mount my PSU for the IKEA LACK table enclosure slightly differently that the PSU bracket, and this one is designed to fit in the opposite orientation around the corner leg with the wire trench.

... compromising durability. Replacing traditional wooden parts, it provides a more robust solution for holding your print bed stable. Print Settings: Printer Brand: RepRap Printer: CTC prusa i3 Rafts: No Supports: No Resolution: 0.3 Infill: 50%

SN04 Sensor Delivered Directly to 3D Printer with Auto-Level Sensor Capability

I misplaced a bracket for the mounted filament holder during a relocation, so I built a new one. Anyone utilizing this type of 3D printed frame can likely benefit from having a couple of these available. ...It's designed specifically for an 8mm bolt to...

I created this bracket specifically for LED tapes with 3M stickers to ensure a secure fit around my printer's acrylic edge. ...My goal was to project light through the glass with a sleek aesthetic mod, utilizing the long-dormant tape reel of LEDs that...

However, these brackets are substitutes for the infamous zip-tie mounting method previously used by Prusa. With the introduction of U-bolts and the upgrade to MK2s, I switched to them for my entire fleet. So I was searching for an alternative to...

Swivel bracket for conveyor sensor

... part (works very well). I included an improved version with more surface area to support the bracket. Can also be used to place the stepper motor outside the frame for 300x200mm beds but you have to drill two slots for the belt into your frame.

A versatile upgrade to the standard mount bracket for y-axis motors, featuring an effortless installation and removal process that requires only a screwdriver. The adjustable design allows for easy alignment of the belt in a straight line. Suitable...

... fitment issues, let me know. I printed an earlier version that was too loose, but I fixed that problem so it should be good now. **Print Settings** * Printer: Original Prusa i3 MK2 * Rafts: None * Supports: None * Resolution: 0.2mm * Infill: 30%

Photoelectric Water / Liquid Level Sensor For ArduinoSell your CAD models on Loadmart.com

For the bracket assembly, insert M3 nuts into the recesses, short M3 screws into the retaining bar's holes, place the servo in its designated spot, secure it with servo mounting screws, and slide the bracket under the stepper motor. Make sure it's...

E3D 40*40 high performance axial fan for Prusa i3

I remix this part for Prusa I3 pro B

Spool holder for Prusa i3 MDF 6mm and M8 screw.

This is the replacement you can print after you super glued the broken part (it works very well).\nI included an improved version with more surface area to hold the bracket.\nThis design can also be used to position the stepper motor outside the...

The design of a custom carriage for Graber i3 and Prusa i3 3D printers with an integrated laser mounting system is underway.

To improve the Z Endstop switch attachment on a MakerFarm i3, I designed an alternative solution. Installing this modification reduced the switch's movement and enhanced the accuracy and consistency of Z-axis homing. Enjoy your improved printing...

LED Bar dimensions: 11.9 x 15.8 x 357mm (Width x Height x Length)\r\n\r\nTo accommodate different sizes of LED lights, simply modify the front design.\r\nInsert the LED power cord into the groove located on the side of the bracket and arrange as...